Rail King SD70ACe Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 56

background image

M.T.H. engines equipped with Proto-Sound 3.0 have speed control capabilities that allow
the engine to maintain a constant speed up and down grades and around curves, much like
an automobile cruise control. You can add or drop cars on the run, and the engine will
maintain the speed you set.

While the engine is programmed to start with the speed control feature activated, you can
opt to turn it off. This means the engine's speed will fall as it labors up a hill and increase
as it travels downward. It is also affected by the addition or releasing of cars while on the
run. Because the engine will run more slowly at a given throttle voltage when speed
control is on than when it is off, you should adjust the throttle to a lower power level for
operation with speed control off to avoid high-speed derailments. When speed control is
off, the volume will drop to allow for better low voltage operation.

To turn speed control on and off

, put the engine in neutral, then quickly tap the

transformer's Horn button one time then quickly tap the Bell button two times, allowing
approximately ½ second to lapse between each quick button press. Two horn blasts will
indicate that the engine has made the change. Repeat the 1 horn, 2 bells code to return it
to the other condition. You will want to do this during the initial neutral upon start-up if
you ever couple this engine to another engine that is not equipped with speed control to
avoid damaging the motors in either engine. Each time you shut down the engine
completely, it will automatically turn speed control on.

Horn

Place

Engine into

Neutral

Bell

Bell

=

Speed Control

Two Horn Blasts

(indicates change is made)

Repeat to Return

to Normal Condition

Locking Locomotive Into A Direction

You can lock your engine into a direction (forward, neutral, or reverse) so that it will
not change directions. To do this, put the engine into the direction you want (or into
neutral to lock it into neutral), run it at a very slow crawl (as slowly as it will move
without halting), and quickly but firmly tap the Horn button once followed by three
quick taps of  the Bell button, allowing approximately ½ second to lapse between each
quick button press. Two horn blasts will indicate that the engine has made the change.
The engine will not change direction (including going into neutral) until you repeat the
1 horn, 3 bells code to return the engine to its normal condition, even if  the engine is
kept without power for extended periods of  time.

Horn

Place

Engine into

Desired

Direction

Horn

Bell

Bell

Bell

=

Direction Lock

Two Horn Blasts

(indicates change is made)

Repeat to Return

to Normal Condition

Speed Control

™

RailKing® SD70ACe Diesel Ready-To-Run Set w/Proto-Sound® 3.0

17

«
...
15
16
17
18
19
...
»

Содержание SD70ACe

























































Отзывы:

Нет отзывов

Похожие инструкции для SD70ACe

Бренд: L. G. B. Страницы: 37

Бренд: marklin Страницы: 44

Бренд: E-FLITE Страницы: 40

CONFECTIONARY AND FRUIT-JUICE STANDS

Бренд: Faller Страницы: 8

AMERICA'S Building Toy SUPERSONIC SWIRL

Бренд: K'Nex Страницы: 24

NORTH AMERICAN T-28 TROJAN

Бренд: SG Models Страницы: 34

Jimmy Neutron boy genius ultra orb

Бренд: Radio Shack Страницы: 8

Бренд: THUNDER TIGER Страницы: 2

Бренд: GREAT PLANES Страницы: 4

Fokker Dr.1 46.7"

Бренд: AerodromeRC Страницы: 25

SnapTite MAX BRAD KESELOWSKI 2 BLUE DEUCE FORD FUSION

Бренд: REVELL Страницы: 8

Hot Wheels Dune Racer W6201

Бренд: Fisher-Price Страницы: 28

Бренд: Zapf Creation Страницы: 48

Zoom Lynx Mk.8 seatbelts STEEL

Бренд: Eduard Страницы: 4

Flight 2 Channel Series

Бренд: Flying Gadgets Страницы: 6

Бренд: Faller Страницы: 8

Chiemgau Alpine Chalet

Бренд: Faller Страницы: 8

RAHDEN HORSE-DRIVEN MILL

Бренд: Faller Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды