Rail King SD70ACe Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 56

background image

™

RailKing® SD70ACe Diesel Ready-To-Run Set w/Proto-Sound® 3.0

CV57 - Anti-Jackrabbit

• This either enables or disables the feature whereby in Conventional DC one has to
lower the track voltage below approx 9VDC and then raise it again to get the engine to
move

• The only method to enable/disable this feature is through DCC

•

This feature is ONLY utilized in Conventional DC. It does not have support

for DCS, Conventional AC, or DCC

• CV57 is the CV used to toggle this. Writing a value of 7 to CV57 will disable the
feature. Writing a value of 0 to CV57 will re-enable the feature

• This feature was borne out of the request for those with automated systems that shut
down the track power to avoid collisions and for traffic management.

Operational Note –

If you are running in Conventional and you have anti-

jackrabbit disabled, your engine will not play any start-up sounds or shut down
sounds. Once the charge light goes out it will just be at the engine’s normal idle
sounds. Likewise, when you remove track power there will be no shut down
sounds. It will just be idle sounds until the super caps shut the board off

By default anti-jackrabbit is enabled at the factory.

1. To disable anti-jackrabbit ensure the engine is running in DCC

2. Connect the DCC system to the engine and power on the DCC system

3. Hit F3 or scroll the speed up to get the engine started up

4. Enter Programming on the Main (PoM)

5. Select CV57 and write a value of 7

6. The engine will give you a two honk response

7. This setting will now be saved and the engine will now operate with anti-jackrabbit
deactivated.

NOTE – Again, Anti-Jackrabbit operation only applies to

Conventional DC

8. To re-activate anti-jackrabbit repeat the above steps except write a value of 0 to
CV57

33

«
...
31
32
33
34
35
...
»

Содержание SD70ACe

























































Отзывы:

Нет отзывов

Похожие инструкции для SD70ACe

Бренд: marklin Страницы: 44

Clickables Fairy Charms IM-21300B

Бренд: Techno Source Страницы: 1

CONFECTIONARY AND FRUIT-JUICE STANDS

Бренд: Faller Страницы: 8

Бренд: LEGO Страницы: 176

KID K’NEX 123 SEASAME STREET Ernie Building Set 85503

Бренд: K'Nex Страницы: 2

Бренд: Zhejiang Jiajia Ride-On Co. Страницы: 27

Бренд: Faller Страницы: 4

ARCHITECTURE BIG BEN

Бренд: LEGO Страницы: 68

100 MODEL IMAGINE BUILDING SET

Бренд: K'Nex Страницы: 83

Бренд: LEGO Страницы: 108

Mephisto Chess Challenger

Бренд: Saitek Страницы: 64

CY8025 Stinson Reliant

Бренд: CYmodel Страницы: 8

Бренд: Science mad Страницы: 34

4-8-4 Northern Steam Locomotive and Tender

Бренд: Lionel Страницы: 12

Бренд: Estes Страницы: 2

Top Spin 140431

Бренд: Faller Страницы: 28

CrusH SWEET TREATS STUDIO 47350

Бренд: Orbeez Страницы: 2

Бренд: NOCH Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды