RACOM RAy3-11 Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 241

background image

A very useful tool for identifying in-band interference and locating a free channel. It is not a full-blown
spectrum analyzer as it scans the spectrum with 2 MHz channel resolution. The accuracy of measured
results is given by the accuracy of measuring RSS.

Enable

Opening analyzer functions.

Start

Interrupts communication on the link and starts scanning frequencies in the band.

Spectrum measure time

Selection of measurement length in range:

Mute peer TX

The deactivation of Peer station transmission during measurement. single sweep … up to 15 min

Note

Single sweep takes about 2 seconds for the whole band scan in 17 or 24 GHz (only 200-250
MHz wide). For licensed bands it takes adequately longer - according the width of RX and TX
parts of the band.

The link is automatically re-established after it is finished.

Warning

Running spectrum measurement causes interruption of user data flow between stations!

Interruption of the scan before selected measure time can be achieved anytime by visiting any of the

settings and select Refresh. This restores the configuration connection (message Peer:

n/a).

5.6.2.4. Radio loopback

Fig. 5.46: Menu Tools > Live Data > Radio loopback

Radio loopback measurement serves as a check of quality of the antenna connection to the microwave
unit and the quality of the antenna itself. Only available for the 17 GHz and 24 GHz units. The function
provides indicative measurement of an antenna parameter CPI (Cross-Port Isolation). It is done by
evaluation of strength of the signal in other (RX) polarization received from its own transmitter (trans-

161

© RACOM s.r.o. – RAy3 Microwave Link

Configuration

«
...
159
160
161
162
163
...
»

Содержание RAy3-11


















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RAy3-11

Бренд: Panasonic Страницы: 24

Бренд: E+E Elektronik Страницы: 2

Бренд: Ocean Signal Страницы: 2

Бренд: Badger Meter Страницы: 4

Бренд: Daiichi Electronics Страницы: 14

Бренд: Chiayo Страницы: 8

Бренд: Yaesu Страницы: 15

Бренд: Target Страницы: 10

Бренд: E+E Elektronik Страницы: 16

Бренд: BW Broadcast Страницы: 49

Бренд: AERF Страницы: 2

Бренд: Sennheiser Страницы: 8

Бренд: FlySky Страницы: 3

Бренд: Vaisala Страницы: 52

Бренд: Mpow Страницы: 12

Бренд: Sole Digital Страницы: 17

Бренд: Zaxcom Страницы: 37

Бренд: Strong Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды