RACOM RAy3-11 Скачать руководство пользователя | Manualshive

Страница: 106 / 241

background image

Voltage max [V]

Default >58
Upper threshold of supply voltage. Active if voltage rises above max voltage threshold.
The same SNMP trap (same OID) applies for both Voltage min and max.

RSS [dBm]

Default <-80
Received Signal Strength. Active if RSS drops below RSS threshold.

MSE [dB]

Default >0
Mean Square Error (the inverse to often used SNR - Signal to Noise Ratio). Active if MSE rises
above MSE threshold.

BER [-]

Default >10e

-6

Bit Error Rate is registered at the receiving end of the link - instantaneous value. Active if BER ex-
ceeds the threshold set in this parameter.

Net bitrate [Mbps]

Default >0
The system warning is generated when the current transfer capacity of radio channel is lower than
the threshold set in this parameter.

Air link down

Default on
Interruption of radio link. Active if radio link is interrupted and units can not communicate by Air.

Eth1/Eth2 link down

Default off
Corresponding user Eth link (Eth1/Eth2) on station interrupted.

Note

The "EthX link" system alarm can only be activated if this alarm is Enabled. When the alarm
is not Enabled, the "EthX link" alarm on

screen is always "Ok" regardless of the

current status of the Ethernet link.

WiFi Management

Default on
Warning is generated when WiFi passphrase is not set or WiFi adapter (and Host Access Point) is
permanently enabled (WiFi Force Enable is ON). Parameter can not be changed in web interface
(only through CLI).

Supply voltage out of range

(RAy3-18 only)
Default off.
Active if voltage before boot is outside of unit voltage range (printed on the unit

Product label

). In-

dicated also by the system

(no color).

Note

The unit does not fully boot. Re-boot the unit by re-powering it with a proper power supply.

RAy3 Microwave Link – © RACOM s.r.o.

106

Configuration

«
...
104
105
106
107
108
...
»

Содержание RAy3-11


















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RAy3-11

Бренд: Datcon Страницы: 40

Бренд: Magnetrol Страницы: 16

Бренд: Ocean Signal Страницы: 2

Бренд: X-Boss Страницы: 2

Бренд: Vanderbilt Страницы: 5

Freeview ZMX-7500

Бренд: Zinwell Страницы: 13

Бренд: aci Страницы: 8

Бренд: aci Страницы: 4

Бренд: SOMFY Страницы: 24

Бренд: Minicom Страницы: 4

Бренд: Sennheiser Страницы: 2

Бренд: Aiwa Страницы: 38

Бренд: Spotwave Страницы: 2

Бренд: ASTRO Страницы: 2

Бренд: M-system Страницы: 3

Audio-Transceiver-CAT

Бренд: G&D Страницы: 44

Бренд: Cable AML Страницы: 26

HYPERVISIONT HV-300 Series

Бренд: Raymarine Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды