RACOM RAy3-11 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 241

background image

with power consumption up to the limit specified in

unit's technical parameters

(i.e. 2.5 W in

the case of 80 GHz unit and 1.25 W in the case of all other models)., but RACOM cannot
guarantee their complete compatibility with RAy units.

Important

SFP/SFP+ module has to be inserted to out-of-power unit, otherwise its function is unpredictable
and the module and/or the unit can be damaged.
Do not remove the smaller plastic screw next to ETH2 label. It is part of the cabinet and assures

pressure equalization

outside and inside.

1.3.3. DC power (using ETH1+POE)

Fig. 1.9: Power supply connector

Fig. 1.10: DC-RJ45 adapter

Direct DC power source can be used to power the RAy3 unit.
Instead of standard DC connector the DC cable is mounted to
a terminal block on DC/RJ45 adapter (item

12

).

The adapter is then fitted in to the RJ45 connector in slot

.

Item

is orderable with the unit (see

tion 1.7.1, “RAy units”

). It is equipped by 2 terminals (each max

2 A / 1.5 mm

2

/ AWG 14) with screws to ensure perfect connec-

tion with cooper DC power cable.
Internal RJ45 pins wiring of DC/RJ45 adapter utilizes all
8 contacts on RJ45 and is:

• DC terminal (+) RJ45 pins: 1,2,4,5
• DC terminal (-) RJ45 pins: 3,6,7,8
• RJ45 shield

floating (not connected to any pin)

Both polarities are supported. Supported voltage range depends
on the maximum power consumption of each model. Those
are:

•

20 to 60 V

for 10, 17 and 24 GHz units (for unit boot at least 21 V

to prevent booting with discharged 24 V battery)

•

37 to 60 V

for 11, 18 and 80 GHz units

Maximum long-term voltage on the unit is recommended to be below
58 V (to ensure over-voltage protection inside the unit stays deac-
tivated). Power input is galvanically separated inside the unit.

Important

The optional shielding of the DC cable has to be properly
grounded near the unit to ensure proper resistance against
over-voltage. Suitable grounding kit (for example item

14

or similar) has to be applied and connected to the mast or to the

on the well grounded unit chassis (for example by the item

15

).

12

https://www.racom.eu/download/hw/ray/free/eng/07_prislusenstvi/OTH-DC-RJ45.pdf

13

https://www.racom.eu/eng/products/microwave-link.html#accessories_poe

14

https://www.racom.eu/eng/products/microwave-link.html#accessories_zemneni

15

https://www.racom.eu/eng/products/microwave-link.html#accessories_zemneni

21

© RACOM s.r.o. – RAy3 Microwave Link

Product

«
...
19
20
21
22
23
...
»

Содержание RAy3-11


















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RAy3-11

Бренд: IDS Страницы: 24

Бренд: NAIM Страницы: 26

Бренд: Nautel Страницы: 92

Бренд: Yaesu Страницы: 195

Бренд: Yaesu Страницы: 39

Бренд: Akai Страницы: 33

Tourguide Wireless Transmitter SR 2020 D

Бренд: Sennheiser Страницы: 32

STINGER2 433TSD22V2

Бренд: Transmitter Solutions Страницы: 2

Бренд: Zaxcom Страницы: 30

Бренд: Aiwa Страницы: 38

Бренд: HBM Страницы: 108

Бренд: marklin Страницы: 36

FT-FOTR-1V-ST-S

Бренд: Fiber Tronix Страницы: 4

Бренд: Yaesu Страницы: 20

Бренд: Boss Audio Systems Страницы: 23

Бренд: Covid Страницы: 11

Cinergy 800 ePVR

Бренд: TerraTec Страницы: 14

Бренд: Icom Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды