Racepak 250-DS-IQ3SL Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 63

Racepak 250-DS-IQ3SL Скачать руководство пользователя страница 47

IQ3 Street Logger Dash Installation Manual

47

Next, insert the memory card in the memory card reader. Now click on the button labeled Set IQ3

Time and Date and follow the online instructions.

This procedure writes a file that contains the current time and date on the memory card. For the

time to be set accurately, you must immediately remove the memory card from your PC’s card
reader, place it back in to the IQ3 Street Logger Dash and turn on the power for at least 5 seconds.

MicroSD Flash Card Reader Installation

Data recorded by the IQ3 Street Logger Dash is stored on a microSD memory card. In order to

transfer the data to the user’s PC, it is necessary to utilize a microSD memory card reader.    A
microSD card reader is included in the IQ3 Street Logger Dash kit package.  The reader requires an
available USB port on your PC.

The microSD memory card reader provided with the IQ3 Street Logger Dash does not support

Windows 95 or Windows 98 operating systems.

Clearing Data Files from the Memory Card

Clearing run data files after each data upload is not required but it is highly recommended that you

do not allow too many run data files to build up.  Storing too many data files on the memory card
can also make it more difficult to identify the proper run data file on future uploads.  Eventually the
memory card will fill to capacity, and the data logger will no longer be able to record data.  You can
clear the data files from the memory card by performing the following procedure:

1)

Start the DataLink II software and open your Car Configuration file by Clicking on File from
the Menu bar and selecting Open Car Configuration. Select the configuration file named
IQ3_Street_Config and click OK

«
...
45
46
47
48
49
...
»

Содержание 250-DS-IQ3SL
































































Отзывы:

Нет отзывов