RAB Lighting Gotcha! Plus GT500 Скачать руководство пользователя

Страница: 4 / 13

•

All wiring MUST comply with local
electrical codes and should be installed
by qualified electrician.

•

Read entire Installation Manual before
proceeding.

TURN OFF POWER BY REMOVING
POWER FUSE OR TURNING OFF CIRCUIT
BREAKER BEFORE INSTALLATION.

• Total lighting load to Gotcha must not

exceed:

500W incandescent @ 120V

1000W incandescent @ 277V

500W LED @ 120V with 0.8 pF Driver

1000W LED @ 277V with 0.8pF Driver

To switch more wattage, an electrician
can install an additional relay.

Gotcha! Mounting and Wiring

Cautions

• Line Carrier Remote Control Systems

such as X-10, Leviton or Radio Shack
are incompatible with sensors and can
cause false activations.

• Do not install on circuits feeding motor

loads such as kitchen appliances, HVAC
equipment, washer/ dryer or garage
door openers.

• Sensor functions best when movement

is across its detection pattern, not
towards the sensor.

• Mount 6’-12’ high for optimum range

and direction.

Mounting(GT500R)

Gotcha floodlight kits come pre-wired and assembled on the RAB CU4 EZ plate,
allowing for mounting on round, rectangular or octagonal surface or recessed box.

GT500R Surface Junction Box Installation:

Attach

Cross Bar

Surface Junction Box

using three bar screws (supplied).

Bring sensor wires through the

Surface Adaptor Plate

Make connections to the supply wires in the junction box according to the

“Basic Kit Wiring” diagram on pg 5.

Push connected wires into the

Surface Junction box

Place the

O-Ring

over the

1/4-20 Screw

and insert into the center of the

cover plate and tighten. Use

Cap

to cover opening.

1/4-20 Screw with

O-Ring and Cap

Surface Adaptor

Plate

Wall

Cross Bar

& screw

Surface Junction Box

Gasket

FIG 1 SURFACE JUNCTION BOX INSTALLATION

Содержание Gotcha! Plus GT500














Результаты поиска

Содержание Gotcha! Plus GT500

Отзывы:

Похожие инструкции для Gotcha! Plus GT500

Бренды по названию

Популярные бренды

RAB Lighting Gotcha! Plus GT500, Руководство по установке

Результаты поиска

Содержание Gotcha! Plus GT500

Отзывы:

Похожие инструкции для Gotcha! Plus GT500

Бренды по названию

Популярные бренды