Quectel M50 Скачать руководство пользователя

Страница: 29 / 89

M50 Hardware Design

M50_HD_V2.0

- 29 -

3.2. Operating modes

The table below briefly summarizes the various operating modes in the following chapters.

Table 7: Overview of operating modes

Mode

Function

Normal operation

GSM/GPRS

SLEEP

The module will automatically go into SLEEP mode if DTR

is set to high level and there is no interrupt (such as GPIO

interrupt or data on UART port).

In this case, the current consumption of module will reduce

to the minimal level.

During SLEEP mode, the module can still receive paging

message and SMS from the system normally.

GSM IDLE

Firmware is active. The module has registered to the GSM

network, and the module is ready to send and receive GSM

data.

GSM TALK

GSM connection is ongoing. In this mode, the power

consumption is decided by the configuration of Power

Control Level (PCL), dynamic DTX control and the working

RF band.

GPRS IDLE

The module is not registered to GPRS network. The module

is not reachable through GPRS channel.

GPRS

STANDBY

The module is registered to GPRS network, but no GPRS

PDP context is active. The SGSN knows the Routing Area

where the module is located at.

GPRS

READY

The PDP context is active, but no data transfer is ongoing.

The module is ready to receive or send GPRS data. The

SGSN knows the cell where the module is located at.

GPRS DATA

There is GPRS data in transfer. In this mode, power

consumption is decided by the PCL, working RF band and

GPRS multi-slot configuration.

Power down

Normal shutdown by sending the “AT+QPOWD=1” command, using the

PWRKEY or the EMERG_OFF

pin. The power management ASIC

disconnects the power supply from the base band part of the module, and only

the power supply for the RTC is remained. Software is not active. The UART

interfaces are not accessible. Operating voltage (connected to VBAT) remains

applied.

Minimum

functionality

mode (without

removing power

supply)

“AT+CFUN” command can set the module to a minimum functionality mode

without removing the power supply. In this case, the RF part of the module

will not work or the SIM card will not be accessible, or both RF part and SIM

card will be disabled, but the UART port is still accessible. The power

consumption in this case is very low.

Quecctel

Confidential

Содержание M50


























































































Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды

Quectel M50, Проектирование аппаратного обеспечения

Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды