Quectel M50 Скачать руководство пользователя

Страница: 2 / 89

M50Hardware Design

M50_HD_V2.0

- 2 -

Document Title

M50 Hardware Design

Revision

2.0

Date

2012-06-26

Status

Released

Document Control ID

M50_HD_V2.0

General Notes

Quectel offers this information as a service to its customers, to support application and

engineering efforts that use the products designed by Quectel. The information provided is

based upon requirements specifically provided for customers of Quectel. Quectel has not

undertaken any independent search for additional information, relevant to any information

that may be in the customer’s possession. Furthermore, system validation of this product

customer or the customer’s system integrator. All specifications supplied herein are subject to

change.

Copyright

This document contains proprietary technical information of Quectel Co., Ltd. Copying this

document, distribution to others, and communication of the contents thereof, are forbidden

without permission. Offenders are liable to the payment of damages. All rights are reserved in

the event of a patent grant or registration of a utility model or design. All specifications

supplied herein are subject to change without notice at any time.

Quecctel

Confidential

Содержание M50


























































































Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды

Quectel M50, Проектирование аппаратного обеспечения

Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды