Quectel M50 Скачать руководство пользователя

Страница: 35 / 89

M50 Hardware Design

M50_HD_V2.0

- 35 -

STATUS pin, which is a low level voltage in this mode.

3.4.2.2. Power down module using AT command

Customer’s application can turn off the module via AT command “AT+QPOWD=1”. This

command will let the module to log off from the network and allow the firmware to save

important data before completely disconnecting the power supply, thus it is a safe way.

Before the completion of the power down procedure the module sends out the result code shown

below:

NORMAL POWER DOWN

After that moment, no further AT commands can be executed. And then the module enters the

power down mode, only the RTC is still active. The power down mode can also be indicated by

STATUS pin, which is a low level voltage in this mode.

Please refer to the

document [1]

for details about the AT command “AT+QPOWD”.

3.4.2.3. Over-voltage or under-voltage automatic shutdown

The module will constantly monitor the voltage applied on the VBAT, if the voltage is

≤

3.5V,

the following URC will be presented:

UNDER_VOLTAGE WARNING

If the voltage is

≥

4.5V, the following URC will be presented:

OVER_VOLTAGE WARNING

The normal input voltage range is from 3.3V to 4.6V. If the voltage is > 4.6V or < 3.3V, the

module would automatically shutdown itself.

If the voltage is < 3.3V, the following URC will be presented:

UNDER_VOLTAGE POWER DOWN

If the voltage is > 4.6V, the following URC will be presented:

OVER_VOLTAGE POWER DOWN

Note: These result codes do not appear when autobauding is active and DTE and DCE are not

Quecctel

Confidential

Содержание M50


























































































Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды

Quectel M50, Проектирование аппаратного обеспечения

Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды