Quectel M50 Скачать руководство пользователя

Страница: 46 / 89

M50 Hardware Design

M50_HD_V2.0

- 46 -

3.9.2. Debug Port

Debug Port



Two lines: DBG_TXD and DBG_RXD



It outputs log information automatically.



Debug Port is only used for firmware debugging and its baud rate must be configured as

460800bps.

Computer

TXD

RXD

GND

Module (DCE)

Debug port

DBG_TXD

DBG_RXD

GND

Figure 22

: Reference design for Debug Port

3.9.3. Auxiliary UART Port

Auxiliary UART Port



Two data lines: TXD_AUX and RXD_AUX



Auxiliary UART port is used for AT command only and does not support GPRS data, CSD

FAX, Multiplexing function etc.



Auxiliary UART port supports the communication baud rates as the following:

4800, 9600, 14400, 19200, 28800, 38400, 57600, 115200.



The default baud rate setting is 115200bps, and does not support autobauding. The baud rate

can be modified by AT+QSEDCB command. For more details, please refer to the

document

[1].

Quecctel

Confidential

Содержание M50


























































































Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды

Quectel M50, Проектирование аппаратного обеспечения

Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды