Quectel BG96 Скачать руководство пользователя страница 14

Страница: 14 / 80

LPWA Module Series

BG96 Hardware Design

BG96_Hardware_Design 13 / 79

“*” means under development.

Within operation temperature range, the module is 3GPP compliant.

SMS

Text and PDU mode

Point to point MO and MT

SMS cell broadcast

SMS storage: ME by default

(U)SIM Interface

Support USIM/SIM card: 1.8V, 3.0V

Audio Feature*

Support one digital audio interface: PCM interface

USB Interface

Compliant with USB 2.0 specification (slave only) and the data transfer rate

can reach up to 480Mbps

Used for AT command communication, data transmission, GNSS NMEA

output, software debugging and firmware upgrade

Support USB serial drivers for Windows 7/8/8.1/10, Linux 3.x(3.4 or

later)/4.1~4.15, Android 4.x/5.x/6.x/7.x/8.x/9.x

UART Interfaces

UART1:



Used for data transmission and AT command communication



115200bps by default



The default frame format is 8N1 (8 data bits, no parity, 1 stop bit)



Support RTS and CTS hardware flow control

UART2:



Used for module debugging and log output



115200bps baud rate

UART3:



Used for outputting GNSS data or NMEA sentences



115200bps baud rate

AT Commands

3GPP TS 27.007 and 3GPP TS 27.005 AT commands, as well as Quectel

enhanced AT commands

Network Indication

One NETLIGHT pin for network connectivity status indication

Antenna Interfaces

Main antenna (ANT_MAIN) and GNSS antenna (ANT_GNSS) interfaces

Physical Characteristics

Dimensions: (26.5±0.15)mm × (22.5±0.15)mm × (2.3±0.2)mm

Weight: approx. 3.1g

Temperature Range

Operation temperature range: -35°C ~ +75°C

Extended temperature range: -40°C ~ +85°C

Storage temperature range: -40°C ~ +90°C

Firmware Upgrade

USB interface, DFOTA

RoHS

All hardware components are fully compliant with EU RoHS directive

NOTES

Содержание BG96

















































































Результаты поиска

Содержание BG96

Отзывы:

Похожие инструкции для BG96

Бренды по названию

Популярные бренды

Quectel BG96, Руководство пользователя

Результаты поиска

Содержание BG96

Отзывы:

Похожие инструкции для BG96

Бренды по названию

Популярные бренды