Quectel BG96 Скачать руководство пользователя страница 37

Страница: 37 / 80

LPWA Module Series

BG96 Hardware Design

BG96_Hardware_Design 36 / 79

In order to enhance the reliability and availability of the (U)SIM card in applications, please follow the

criteria below in (U)SIM circuit design:



Keep the placement of (U)SIM card connector as close to the module as possible. Keep the trace

length as less than 200mm as possible.



Keep (U)SIM card signals away from RF and VBAT traces.



Assure the ground between the module and the (U)SIM card connector short and wide. Keep the

trace width of ground and USIM_VDD no less than 0.5mm to maintain the same electric potential.

Make sure the bypass capacitor between USIM_VDD and USIM_GND less than 1uF, and place it as

close to (U)SIM card connector as possible. If the system ground plane is complete, USIM_GND can

be connected to the system ground directly.



To avoid cross-talk between USIM_DATA and USIM_CLK, keep them away from each other and

shield them with surrounded ground. USIM_RST should also be ground shielded.



In order to offer good ESD protection, it is recommended to add a TVS diode array with parasitic

capacitance not exceeding 15pF. In order to facilitate debugging, it is recommended to reserve series

resistors for the (U)SIM signals of the module. The 33pF capacitors are used for filtering interference

of EGSM900. Please note that the (U)SIM peripheral circuit should be close to the (U)SIM card

connector.



The pull-up resistor on USIM_DATA line can improve anti-jamming capability when long layout trace

and sensitive occasion are applied, and should be placed close to the (U)SIM card connector.

3.9. USB Interface

BG96 contains one integrated Universal Serial Bus (USB) interface which complies with the USB 2.0

specification and supports high-speed (480Mbps) and full-speed (12Mbps) modes. The USB interface is

used for AT command communication, data transmission, software debugging and firmware upgrade. The

following table shows the pin definition of USB interface.

Table 10: Pin Definition of USB Interface

For more details about USB 2.0 specification, please visit http://www.usb.org/home.

Pin Name

Pin No.

I/O

Description

Comment

USB_VBUS

USB connection detection

Typically 5.0V

USB_DP

USB differential data bus (+)

Require differential
impedance of 90Ω

USB_DM

USB differential data bus (-)

GND

Ground

Содержание BG96

















































































Результаты поиска

Содержание BG96

Отзывы:

Похожие инструкции для BG96

Бренды по названию

Популярные бренды

Quectel BG96, Руководство пользователя

Результаты поиска

Содержание BG96

Отзывы:

Похожие инструкции для BG96

Бренды по названию

Популярные бренды