Quectel BG96 Скачать руководство пользователя страница 12

Страница: 12 / 80

LPWA Module Series

BG96 Hardware Design

BG96_Hardware_Design 11 / 79

Product Concept

2.1. General Description

BG96 is an embedded IoT (LTE Cat M1/LTE Cat NB1/EGPRS) wireless communication module. It

provides data connectivity on LTE-TDD/LTE-FDD/GPRS/EGPRS networks, and supports half-duplex

operation in LTE networks. It also provides GNSS

and voice

functionality to meet customers

’ specific

application demands. The following table shows the frequency bands of BG96 module.

Table 1: Frequency Bands of BG96 Module

GNSS function is optional.

BG96 supports VoLTE (Voice over LTE) under LTE Cat M1 network.

BG96 GSM only supports Packet Switch.

LTE-FDD B25 is supported on BG96 of R1.2 hardware version.

“*” means under development.

With a compact profile of 26.5mm × 22.5mm × 2.3mm, BG96 can meet almost all requirements for M2M

applications such as smart metering, tracking system, security, wireless POS, etc.

BG96 is an SMD type module which can be embedded into applications through its 102 LGA pads. BG96

supports internet service protocols like TCP, UDP and PPP. Extended AT commands have been

developed for customers to use these internet service protocols easily.

Module

LTE Bands

GSM

Rx-diversity

GNSS

BG96

Cat M1 & NB1:

LTE-FDD:

B1/B2/B3/B4/B5/B8/B12/

B13/B18/B19/B20/B25

B26*/B28

LTE-TDD:

B39 (for Cat M1 only)

GSM850/EGSM900/

DCS1800/PCS1900

Not Supported

GPS,

GLONASS,

BeiDou/Compass,

Galileo,

QZSS

NOTES

Содержание BG96

















































































Результаты поиска

Содержание BG96

Отзывы:

Похожие инструкции для BG96

Бренды по названию

Популярные бренды

Quectel BG96, Руководство пользователя

Результаты поиска

Содержание BG96

Отзывы:

Похожие инструкции для BG96

Бренды по названию

Популярные бренды