Quadra-Fire 7100FP-BK-B Скачать руководство пользователя страница 28

Страница: 28 / 48

Attach

Flue First

CAK4A

Secure with Screws

Provided

Push Together

Secure to Top

C. Install Chimney Air kit (CAK4A)

NOTICE:

Chimney Air Kit, Part CAK4A is required when

using the SL-300 Pipe Series. Detailed instructions are

supplied with the kit. If using the Dura-Plus System (must

be 8 in./203 mm in diameter), the starter ring that came

with the fireplace must be removed and replaced with the

Dura-Plus Base Plate. The CAK4A is not required with a

Dura-Plus System.

• Install the chimney pipe first.

• Hand bend the tabs in position before placing on the

fireplace.

• Place the box on top of the fireplace around the chimney

pipe, push both pieces together and secure with screws

provided.

• Use the pre-punched holes in the tabs as guides and

drill holes through the fireplace top.

• Secure the CAK4A in place. See Figure 6.3.

• Seal around the kit at the flue and at the top of the can

with caulk. See Figure 6.3.

Figure 6.3 Installing the CAK4A

NOTICE:

Chimney sections cannot be disassembled once

locked together. Plan ahead!

• Lock chimney sections and/or offsets/returns together by

pushing downward until the top section meets the stop

bead on the lower section.

• Pull on the top section to make sure it is fully engaged

and will not separate.

• You may use #6 or #8 sheet metal screws no longer than

1/2 in. (13 mm) to fasten chimney sections together. Do

NOT penetrate inner flue.

WARNING!

Risk of Fire!

You MUST use screws (pro-

vided) to fasten offset/returns to chimney sections to

keep the chimney parts from twisting. Failure to do so

could cause fire.

• Fasten offset/returns to chimney sections. Insert the

screws (provided) through the predrilled holes. Do NOT

penetrate inner flue.

• Secure chimney returns with hanger straps provided;

fasten to studs or joists.

• Vertical straight runs of chimney must be supported every

35 ft (10.7 m).

B. Assemble Chimney Sections

Use only those components described in this manual.
Substitute or damaged chimney components could impair

safe operation and cause overheating and fire.
Attach either a straight chimney section or an offset to

the top of the fireplace (depending on your installation

requirement). Chimney sections are locked together by

pushing downward until the top section meets the stop

bead on the lower section.
The inner flue is placed to the inside of the flue section

below it. The outer casing is placed outside the outer cas-

ing of the chimney section below it. See Figure 6.2.

WARNING! Risk of Fire! DO NOT

install substitute or

damaged chimney components.

Figure 6.2 Assembling Chimney Sections

Quadra-Fire • 7100 FP • 433-3610 Installation Manual • Rev G • 5/27/14

Содержание 7100FP-BK-B

















































Результаты поиска

Содержание 7100FP-BK-B

Отзывы:

Похожие инструкции для 7100FP-BK-B

Бренды по названию

Популярные бренды

Quadra-Fire 7100FP-BK-B, Руководство по установке

Результаты поиска

Содержание 7100FP-BK-B

Отзывы:

Похожие инструкции для 7100FP-BK-B

Бренды по названию

Популярные бренды