Quadra-Fire 7100FP-BK-B Скачать руководство пользователя страница 24

Страница: 24 / 48

6 ft (1.8 m) max.

unsupported

run
20 ft (6.10 m) max.

pipe between an

offset & return

Ceiling firestop

35 ft (10.7 m)

max. straight

unsupported

chimney height

14.5 ft (4.42 m) min. height/single offset-return

20 ft. (6.10 m) min. height/double offset-return

50 ft (15.24 m) max. height

6 ft (1.83 m) max.

unsupported chimney

above roof

45 3/4 in.

(1162 mm)

to top of

standoffs

Attic Insulation Shield

Chimney Air Kit

required with SL

chimney

Figure 5.1 Chimney Requirements

NOTICE:

A maximum of two pairs of offsets and returns

may be used.

Minimum overall straight height

13 ft

3.96 m

Minimum height with single offset/

return

14.5 ft

4.42 m

Double offset/return minimum height

20 ft

6.1 m

Maximum height

50 ft

15.24 m

Maximum chimney length between an

offset and return

20 ft

6.1 m

Maximum distance between chimney

stabilizers

35 ft

10.67 m

Maximum unsupported chimney

length between the offset and return

6 ft

1.83 m

Maximum unsupported chimney

height above the fireplace

35 ft

10.67 m

Maximum unsupported chimney

above roof

6 ft

1.83 m

WARNING! Risk of Fire!

You must maintain 2 in. (51 mm)

air space clearance to insulation and other combustible

materials around the chimney system. Failure to do so

may cause overheating and fire.

NOTICE

You must provide support for the pipe during

construction and check to be sure inadvertent loading has

not dislodged the chimney section from the fireplace or at

any chimney joint.

A. Chimney Requirements

Vertical distances are measured from the base of the

fireplace as shown in Figure 5.1.

Chimney and Termination Requirements

Table 5.2 Chimney Component Dimensions

Table 5.1 Chimney Requirements

HEIGHT OF CHIMNEY COMPONENTS

in.

Chimney Stabilizer

SL3

4-3/4

121

Offsets/Returns

SL315

13-3/8

340

SL330

15-1/2

394

Chimney Sections*

SL306

4-3/4

121

SL312

10-3/4

273

SL318

16-3/4

425

SL324

22-3/4

578

SL336

34-3/4

883

SL348

46-3/4

1187

* Dimensions reflect effective height.

Quadra-Fire • 7100 FP • 433-3610 Installation Manual • Rev G • 5/27/14

Содержание 7100FP-BK-B

















































Результаты поиска

Содержание 7100FP-BK-B

Отзывы:

Похожие инструкции для 7100FP-BK-B

Бренды по названию

Популярные бренды

Quadra-Fire 7100FP-BK-B, Руководство по установке

Результаты поиска

Содержание 7100FP-BK-B

Отзывы:

Похожие инструкции для 7100FP-BK-B

Бренды по названию

Популярные бренды