Quadra-Fire 7100FP-BK-B Скачать руководство пользователя страница 22

Страница: 22 / 48

Securely Twist

Lock B-Vent to

Adapter

Secure B-Vent to Fan Housing

with sheet metal screws

Return Air Grille

Install with Louvers

pointed down

Bracket

Can rotate

180

2 x 4 Wall

Fan Housing

1/2 in. (13mm)

clearance to

combustibles

must be

maintained.

2 x 4 wall

Sheet Rock

Leave 1/4" (6mm) clearance

from all 4 outer edges

Seal grille using gasketing supplied with the kit

• Install the variable speed wall rheostat (with setting on

“OFF”) in a convenient location. This switch will control

the Heat-Zone fan operation.

• Remove the junction box. Wire 110 VAC service TO

the wall rheostat and FROM the wall rheostat to the

fan junction box. Use wire nuts to secure the 110 VAC

service wires to the hot (black) and neutral (white) fan

wires and screw the 110 VAC ground wire to the junction

box. See Figure 3.21.

• Secure the return air grille to the fan housing making

sure it is flush. The grille must be installed with the

louvers pointing down.

NOTICE:

DO NOT USE ADJUSTABLE REGISTERS.

Junction Box Removed

Wire Clamp

Wire Nuts

Junction Box

Black

White

NOTICE:

Secure the duct so that clearance to the fire-

place outer wrap is maintained. Tape all seams with alumi-

num tape 1-1/4 in. (32 mm) minimum width or as specified

by local codes.)

• Seal all the way around the inside of the return air grille to

prevent hot air being drawn back into the venting system

using gasketing supplied with the kit. Leave 1/4 in. (6

mm) clearance from all four outer edges. Trim excess

gasketing. See Figure 3.20.

Figure 3.18

Figure 3.19

Figure 3.20

Figure 3.21

Quadra-Fire • 7100 FP • 433-3610 Installation Manual • Rev G • 5/27/14

Содержание 7100FP-BK-B

















































Результаты поиска

Содержание 7100FP-BK-B

Отзывы:

Похожие инструкции для 7100FP-BK-B

Бренды по названию

Популярные бренды

Quadra-Fire 7100FP-BK-B, Руководство по установке

Результаты поиска

Содержание 7100FP-BK-B

Отзывы:

Похожие инструкции для 7100FP-BK-B

Бренды по названию

Популярные бренды