Quadra-Fire 7100FP-BK-B Скачать руководство пользователя страница 31

Страница: 31 / 48

Installation of a ceiling firestop is required:

• Refer to Figures 6.7, 6.8, 6.9.

• Roll the shield (around the chimney if already installed).

The three holes on each side will match up (large holes

on top).

• Insert three screws into the matching holes to form a

tube.

• Bend the tabs on the bottom of the tube inward to 90° to

maintain chimney air space (refer to Figure 6.8).

• Rest the insulation shield on the ceiling firestop below.

• Bend the tabs at the top of the shield inward to 90° to

maintain the 2 in. (51 mm) air space from the chimney.

If you wish to make a custom shield or barrier, follow

these guidelines:

• Metal is preferred, although any material stiff enough to

hold back the insulation can be used.

WARNING!

Risk of Fire!

Use of cardboard or other

materials that can deflect under humidity or other envi-

ronmental conditions is not recommended.

• The shield or barrier must be tall enough to extend

above the insulation and prevent blown-in insulation from

spilling into the cavity.

• Maintain specified air spaces around chimney.

• Check instructions and local codes for further details.

Insert three

screws

Tabs bent 90°

Figure 6.7 Prepare Attic Insulation Shield

Tabs

bent in 90°

and taped

Tabs bent 90° to

rest against pipe

Attic Insulation Shield

Ceiling Firestop

10-1/2 in.

(267 mm)

14-1/2 in. (368 mm)

diameter

Insulation

Pipe

2 in. (51 mm)

air space

Tabs

bent in 90°

and taped

Tabs bent 90° to

rest against pipe

Attic Insulation Shield

Ceiling Firestop

10-1/2 in.

(267 mm)

14-1/2 in. (368 mm)

diameter

Insulation

Pipe

2 in. (51 mm)

air space

Figure 6.8 Install Attic Insulation Shield (firestop above ceiling)

Figure 6.9 Install Attic Insulation Shield (firestop below ceiling)

F. Install Attic Insulation Shield

WARNING! Risk of Fire!

You MUST install an attic insu-

lation shield when there is any possibility of insulation or

other combustible material coming into contact with the

chimney.
•

DO NOT

pack insulation between the chimney and the

attic insulation shield.

• Failure to keep insulation and other materials away from

chimney pipe could cause fire.

•

DO NOT

offset chimney inside insulation shield.

Double-check the Chimney Assembly

Continue assembling the chimney sections up through

the ceiling firestops as needed. While doing so, be

aware of the height and unsupported chimney length

limitations given under Section 5.
Check each section by pulling up slightly from the top

to ensure proper engagement before installing the suc-

ceeding sections. If they have been connected correct-

ly, they will not disengage when tested.

Quadra-Fire • 7100 FP • 433-3610 Installation Manual • Rev G • 5/27/14

Содержание 7100FP-BK-B

















































Результаты поиска

Содержание 7100FP-BK-B

Отзывы:

Похожие инструкции для 7100FP-BK-B

Бренды по названию

Популярные бренды

Quadra-Fire 7100FP-BK-B, Руководство по установке

Результаты поиска

Содержание 7100FP-BK-B

Отзывы:

Похожие инструкции для 7100FP-BK-B

Бренды по названию

Популярные бренды