Quadra-Fire 7100FP-BK-B Скачать руководство пользователя страница 32

Страница: 32 / 48

G. Roof Penetration

• Refer to Figure 6.10.

• Plumb from roof to center of chimney.

• Drive a nail up through roof to mark center of pipe.

• Measure to either side of nail and mark the 14-1/2 in. x

14-1/2 in. (368 mm x 368 mm) opening required.

• Measure opening on the horizontal; actual length may

be larger depending on roof pitch.

• Cut out and frame opening.

• Refer to

Chapter 25

of the

Uniform Building Code

for

roof framing details.

Figure 6.10 Ceiling/Attic Construction

Install Flashing

• Assemble chimney so it passes through the framed

opening.

• Slip the flashing over the chimney.

NOTICE:

Roofing shingles must be below the flashing

plate on the lower side of a sloped roof and over the

flashing plate on the sides and top.

• Nail the flashing to the roof. Keep gaps between the

flashing plate and the roof to a minimum.

• Caulk the flashing plate and roof junction as well as

the vertical seam on the flashing. All nail heads must

be caulked with a roofing sealant.

• Caulk the overlap seam of any exposed pipe sections

that are located above the roof line to prevent leaks.

CHIMNEY

FLASHING

PLATE

JOISTS

NAIL

THIMBLE

FLASHING

Figure 6.11 Installing Part: 12966A, Configuration 1

NOTICE:

REQUIRED

for manufactured homes.

• Locate the point where the chimney will exit the roof by

plumbing down to the center of the chimney. Lay out,

cut and frame a 14-1/2 in. (368 mm) square opening

(measured on the horizontal) through the ceiling and roof

structure.

Consult local codes for framing details.

• The thimble must extend completely through the roof

structure shielding combustible materials. Five location

holes have been provided to allow for a variety of ceiling/

roof thicknesses. A thimble extension is required when

the ceiling/roof thickness exceeds 12-1/2 in. (318 mm).

The extension should overlap the thimble one inch.

• To attach the extension to the thimble, drill 1/8 in. (3 mm)

holes through the outer shield of the thimble using the

predrilled holes in the extension as guides. Attach the

extension to the thimble using the screws provided with

the extension.

• Install the thimble assembly and nail it securely to the

framing members.

H. Manufactured Home Installation
SL-300 Series Ceiling/Roof Thimble

• Center the flashing over the chimney and nail it to the

roof. Keep gaps between the flashing plate and the roof

to a minimum. Caulk the flashing plate and roof junction

as well as the vertical seam on the flashing. All nail heads

must be caulked with a roofing sealant.

• Finish assembling the chimney storm collar and

termination cap following the installation instructions

provided with them.

Quadra-Fire • 7100 FP • 433-3610 Installation Manual • Rev G • 5/27/14

Содержание 7100FP-BK-B

















































Результаты поиска

Содержание 7100FP-BK-B

Отзывы:

Похожие инструкции для 7100FP-BK-B

Бренды по названию

Популярные бренды

Quadra-Fire 7100FP-BK-B, Руководство по установке

Результаты поиска

Содержание 7100FP-BK-B

Отзывы:

Похожие инструкции для 7100FP-BK-B

Бренды по названию

Популярные бренды