qpcom QP-WO259GHP Скачать руководство пользователя | Manualshive

Страница: 35 / 48

background image

Management and configuration

-35-

Load Settings from File
Click the Browse button to select the configuration files then click the Upload
button to update the selected configuration to the WLAN Access Point.
Reset Settings to Default
Click the Reset button to reset the configuration parameter to factory defaults.

4.15

Password Setup

This page is used to set the account to access the web server of Access Point.
Empty user name and password will disable the protection.

User Name
Fill in the user name for web management login control.
New Password
Fill in the password for web management login control.
Confirmed Password
Because the password input is invisible, so please fill in the password again for
confirmation purpose.

«
...
33
34
35
36
37
...
»

Содержание QP-WO259GHP

















































Отзывы:

Нет отзывов

Похожие инструкции для QP-WO259GHP

Бренд: E-Lins Страницы: 103

Бренд: InfiNet Wireless Страницы: 100

ezWave WAP-1100 Series

Бренд: Widelink Страницы: 50

Бренд: Ruckus Wireless Страницы: 58

Бренд: Sapido Страницы: 21

Бренд: Sapido Страницы: 102

Бренд: Allied Telesis Страницы: 180

Бренд: IOGear Страницы: 85

Бренд: BTI Wireless Страницы: 53

Бренд: Ebyte Страницы: 15

OfficeConnect 3CRWE454A72

Бренд: 3Com Страницы: 86

Бренд: Atlona Страницы: 24

Бренд: Browan Страницы: 72

Бренд: LG-Ericsson Страницы: 34

Бренд: Waldmann Страницы: 16

Бренд: KB VISION Страницы: 23

Бренд: H3C Страницы: 27

Бренд: Ubiquiti Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды