manualshive.com logo in svg

qpcom QP-WO259GHP, Руководство пользователя

Поделиться
Скачать
qpcom QP-WO259GHP Скачать руководство пользователя страница 26

-26-

Wireless Access Control Mode
Click the Disabled, Allow Listed or Deny Listed of drop down menu choose
wireless access control mode.
This is a security control function; only those clients registered in the access
control list can link to this WLAN Access Point.
MAC Address
Fill in the MAC address of client to register this WLAN Access Point access
capability.
Comment
Fill in the comment tag for the registered client.
Apply Changes
Click the Apply Changes button to register the client to new configuration setting.
Reset
Click the Reset button to abort change and recover the previous configuration
setting.
Current Access Control List
It shows the registered clients that are allowed to link to this WLAN Access Point.
Delete Selected
Click to delete the selected clients that will be access right removed from this
WLAN Access Point.
Delete All
Click to delete all the registered clients from the access allowed list.
Reset
Click the Reset button to abort change and recover the previous configuration
setting.

Содержание QP-WO259GHP

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды