Qirod QD100 Series Скачать руководство пользователя страница 70

Страница: 70 / 163

8: First DC brake, then starting. DC braking current level and braking time according to

F507 and F508.

The f500 parameter detects the rotating speed and rotational direction of the motor

during coasting ing the event of momentary power failure, and then after power has been

restored, restarts the motor smoothly (motor speed search function).

This parameter also allows commercial power operation to be switched to inverter

operation without stopping the motor. During operation, "a-08" is displayed. During the

retry mode see f400), the motor speed search function operated automatically as

required and thus allows smooth motor restarting.

At restart, it takes about 300 ms for the inverter to check to see the number of

revolutions of the motor. For this reason, the start-up takes more time than usual. Use

this function when operating a system with one motor connected to one inverter. This

function may not operate properly in a system configuration with multiple motors

connected to one inverter.

Setting f500 =1, (3): This function operates after power has been restored following

detection of an undervoltage by the main circuits and control power.

Setting f500 =2, (3): This function operates after the standby terminal((input terminal

function =1) connection has been opened first and then connected again.

Setting f500 =4, a motor speed search is performed each time operation is started.This

function is useful especially when the motor is not operated by the inverter but it is

running because of external force.

Setting f500 = 0 (Disabled) and disabling the retry function (f400=0), when apply the

inverter to crane or hoist. Such machines may have its load moved downward during the

above waiting time from input of the operation starting command to the restart of the

motor.

NO.

Parameter Name

Setting Range

Default

f501

auto-stop time limit for lower-limit

frequency operation

0.0~600.0s

0.1

0: disabled

（

0.0

）

. None.

1: Enabled

（

0.1~600.0s

）

. If operation is carried out continuously at a frequency below

the lower-limit frequency (f009) for the period of time set with f501, the inverter will enter

Содержание QD100 Series




































































































































































Результаты поиска

Содержание QD100 Series

Отзывы:

Qirod QD100 Series, Руководство пользователя, Страница: 70 / 163

Результаты поиска

Содержание QD100 Series

Отзывы: