PV Electronics Elite Nixie Скачать руководство пользователя | Manualshive

Страница: 34 / 43

background image

Nixie Tube Clock ‘Elite’

Issue 3 (25 July 2018)

www.pvelectronics.co.uk

- 34 -

7.4

Time Synchronisation Function

XTERNA broadcasts every 10 minutes. After configuring your clock,
please be patient in waiting for the first Synchronisation. Upon
synchronisation the yellow LED D7 will illuminate. Remember to set
DST (‘Summer Time’) with the DST button.

7.5

Temperature Display

The temperature is also transmitted with the time. Therefore,
temperature will not be displayed until after the first
synchronisation.
Set Celsius or Fahrenheit using parameter 29:
Fahrenheit: 1
Celsius : 2

Temperature is displayed between 30 and 35 seconds past each
minute. Celsius is displayed with 0.5 °C resolution. Fahrenheit is
displayed with 1 °F resolution.
Positive and negative temperature is indicated by the left hand
neons: Neon indicator PM2 acts as a decimal point.

7.6

Temperature Validity

If no valid data is received on the next scheduled sync (every 10
minutes), the temperature will be deemed to be old and invalid.
Temperature will not be shown until a new valid temperature is
received.

«
...
32
33
34
35
36
...
»

Содержание Elite Nixie












































Отзывы:

Нет отзывов

Похожие инструкции для Elite Nixie

Бренд: iHome Страницы: 2

Бренд: iHome Страницы: 16

Бренд: iHome Страницы: 18

Бренд: HoMedics Страницы: 10

Бренд: Palsonic Страницы: 5

Бренд: Gainsborough Страницы: 2

Бренд: Pyramid Страницы: 20

Бренд: Eurochron Страницы: 8

Бренд: Technoline Страницы: 25

Бренд: JVC Страницы: 32

TE211W - Atomic Clock With Wireless Thermometer

Бренд: Honeywell Страницы: 9

Бренд: Honeywell Страницы: 4

RCW33W - Atomic Wall Clock

Бренд: Honeywell Страницы: 10

Бренд: Honeywell Страницы: 1

Бренд: Honeywell Страницы: 9

Бренд: Honeywell Страницы: 2

Бренд: Honeywell Страницы: 60

Бренд: Honeywell Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды