background image

Nixie Tube Clock ‘Elite’ 

 

Issue 3 (25 July 2018)

 

 

www.pvelectronics.co.uk

 

- 32 - 

Cancelling Alarm

:

  

Press ‘ALARM’ briefly to cancel alarm and enter snooze mode, or a longer 
press until the clock bleeps, to cancel snooze. Alarm remains set for 
subsequent days. 
 

Rapid DST Adjustment

 

Press ‘DST’ briefly to toggle between DST and standard time. The 
indicator shows whether DST mode is active or not.  
 
Note, that GPS time data does not contain DST information, so the DST 
status will need to be set manually in GPS sync mode as well as manual 
time-set mode. 
 

Invoking Cold Start Tube Test

 

A cold start is when the Supercapacitor C7 is discharged. On a cold start, 
time and date are lost and the clock will perform the ascending tube test 
on power up. To force a Cold Start, do the following: 
 

 

Toggle the DST on by pressing the DST button if necessary 

 

From time display, press ALARM once. 

 

Press ADJ once to illuminate the ALARM LED 

 

Immediately disconnect power. 

 
The Power sensing / sleep routine is not called from within the Alarm 
setup, so the clock will drain the supercapacitor via the DST and ALARM 
LEDs. Wait 2-3 minutes until the LEDs are fully off. On powering up 
again, you will get the cold start tube test. 
 

Calibration of Timekeeping Accuracy

 

Over time you may observe the clock runs faster or slower than an 
accurate time standard. You can finely adjust the timekeeping by setting 
configuration parameters 20 and 21. We recommend to precisely set the 
clock against a known accurate clock, and then record the time drift in 
seconds after 5 full days (120 hours). Program this value into parameter 
20. 
Set parameter 21 to 0 to slow down the clock and to 1 to speed up the 
clock. 
 

 

 

Содержание Elite Nixie












































Отзывы: