PV Electronics Elite Nixie Скачать руководство пользователя страница 3

Страница: 3 / 43

Nixie Tube Clock ‘Elite’

Issue 3 (25 July 2018)

www.pvelectronics.co.uk

- 3 -

1. INT

RODUCTION

Here are the key features of the ELITE Nixie:



Hours, Minutes and Seconds display



Direct drive to six medium size Plug-in Nixie Tubes



Supports IN-8, ZM1000, NL840, NL841, NL842, NL844, NL845, NL846,
NL900, NL901 and CK8754



Noiseless, Direct Drive giving optimum digit clarity



Uses a Quartz Crystal Oscillator as the timebase



12 or 24 hour modes



Programmable leading zero blanking



Date display in either DD.MM.YY or MM.DD.YY or YY.MM.DD format



Programmable date display each minute



Scrolling display of date or standard display



Alarm, with programmable snooze period



Optional GPS / XTERNA

synchronisation with status indicator LED



Dedicated DST button to switch between DST and standard time



Supercapacitor backup. Keeps time during short power outages



PIR Motion Sensor input and accessory available. Configurable timeout
period



Simple time setting using two buttons



Configurable for leading zero blanking



Double dot colon neon lamps



11 colon neon modes including AM / PM indication (top / bottom or left /
right), railroad (slow or fast) etc.



Seconds can be reset to zero to precisely the set time



Programmable night mode - blanked or dimmed display to save tubes or
prevent sleep disturbance



Rear Indicator LEDs dim at night to prevent sleep disturbance



Weekday aware ‘Master Blank’ function to turn off HV/ tubes and LEDs on
weekends or during working hours



Separate modes for colon neons during night mode



Standard, fading, or crossfading with scrollback display modes



‘Slot Machine’ Cathode poisoning prevention routine



Programmable RGB tube lighting – select YOUR favourite colour palette



729 colours possible. Have a different colour or your choosing every
hour, or autochanging colours



Not AC frequency dependent – works in all countries



All user preferences stored to non-volatile memory



Additional wireless functions if XTERNA module used:
- Display of outdoor temperature in Celsius or Fahrenheit.
-

Min / Max temperature in last 24 hours

Wireless, Auto Sync of time from GPS with auxilliary TCXO

GPS Sync time, and time since last GPS Fix

Voltage of XTERNA module battery

Содержание Elite Nixie












































Результаты поиска

Содержание Elite Nixie

Отзывы:

Похожие инструкции для Elite Nixie

Бренды по названию

Популярные бренды

PV Electronics Elite Nixie, Инструкция по сборке и руководство пользователя

Результаты поиска

Содержание Elite Nixie

Отзывы:

Похожие инструкции для Elite Nixie

Бренды по названию

Популярные бренды