PV Electronics Elite Nixie Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 43

background image

Nixie Tube Clock ‘Elite’

Issue 3 (25 July 2018)

www.pvelectronics.co.uk

- 10 -

4.

ASSEMBLY OF THE TUBE PCB

4.1 J2 (12 Way Micromatch connector (male))

Clip off the polarization tab from the connector as it is not needed.
Then solder the connector into the tube PCB on the opposite side to
the pre-soldered ICs.

Now, proceed according to the tube type you are using.

4.2 IN-8 and NL84x Nixie Tubes

There are 66 individual sockets that need to be soldered in. The

best method is a follows.

IN-8: Slide 11 sockets onto the 11 pins of the tube.
NL84x: Slide 10 sockets onto the 10 outer pins on the tube. With
reference to the PCB check which one of the inner pins is needed
(the corresponding hole on the PCB is plated), and slide a socket
over this pin too.

«
...
8
9
10
11
12
...
»

Содержание Elite Nixie












































Отзывы:

Нет отзывов

Похожие инструкции для Elite Nixie

Бренд: ZEBON Страницы: 2

Бренд: Sangean Страницы: 18

Бренд: Sangean Страницы: 1

Control Clock 88

Бренд: Cambridge SoundWorks Страницы: 6

Бренд: Ambient Страницы: 30

T4-Watch Outdoor

Бренд: TFA Страницы: 2

Бренд: Sharper Image Страницы: 20

Бренд: Elta Страницы: 57

Бренд: Elta Страницы: 112

Бренд: Jazwares Страницы: 18

Бренд: Morphy Richards Страницы: 2

Бренд: Decotech Страницы: 48

Бренд: RCA Страницы: 3

Бренд: RCA Страницы: 8

Бренд: Naxa Страницы: 24

Бренд: Kruger&Matz Страницы: 75

Бренд: Emerson Research Страницы: 40

Бренд: Hyundai Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды