PV Electronics Elite Nixie Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 43

background image

Nixie Tube Clock ‘Elite’

Issue 3 (25 July 2018)

www.pvelectronics.co.uk

- 24 -

Now the anode leads of the LEDs will be in the correct orientation
as you insert into the holes in the PCB behind the ALARM and DST
switches. Use the jig again, to align the LEDs above the switches.
This will give the correct spacing for if you want to use one of our
cases.

Now bend and solder D7. The longer lead goes in the pad with a
circle around it. Think about the orientation before you bend the
leads. D7 should be level with the GPS jack socket next to it, and
protrude by its full body length from the rear of the PCB.

«
...
22
23
24
25
26
...
»

Содержание Elite Nixie












































Отзывы:

Нет отзывов

Похожие инструкции для Elite Nixie

OneVue Sync Levo C2005

Бренд: Primex Страницы: 30

Бренд: TFA Страницы: 2

Бренд: Insignia Страницы: 29

MUSICDOCK KC-80

Бренд: KLH Страницы: 16

Бренд: Jensen Страницы: 22

Бренд: Howard Miller Страницы: 2

Бренд: Explore Scientific Страницы: 64

Бренд: Explore Scientific Страницы: 68

2G-StarLink TrackerSF

Бренд: ERM Страницы: 17

Бренд: Daikin Страницы: 18

Бренд: La Crosse Technology Страницы: 6

Бренд: Casio Страницы: 3

Бренд: Casio Страницы: 7

Бренд: TDK Страницы: 6

Бренд: uAttend Страницы: 16

Бренд: RCA Страницы: 1

Бренд: Akai Страницы: 12

Бренд: Bush Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды