PV Electronics Elite Nixie Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 43

background image

Nixie Tube Clock ‘Elite’

Issue 3 (25 July 2018)

www.pvelectronics.co.uk

- 17 -

5.3 Testing Low Voltage Power Supply.

Identify the test GND, 5V and HV test points at the side of the PCB.

Plug in the 12V DC power supply, and then test using a DC
voltmeter: Touch the black probe on the GND test point and the
red probe on the 5V test point. The voltage should measure
between 5.6 and 5.9 Volts. If not, disconnect power and check
your work. Do not proceed with the assembly until the error is
corrected. Once the test is completed, disconnect the power.

5.4 High Voltage Generator components.

Socket for IC2
R1, R3 (4.7 KΩ)
R2 (390 KΩ)
C3 (1uF)
C4 (220uF)
D4 (1N5819)
D5 (UF4004)
Q1 (IRFD220)
L2 (100uH Inductor)

«
...
15
16
17
18
19
...
»

Содержание Elite Nixie












































Отзывы:

Нет отзывов

Похожие инструкции для Elite Nixie

Бренд: Jensen Страницы: 14

Бренд: NATURE & DECOUVERTES Страницы: 28

Бренд: La Crosse Technology Страницы: 21

Бренд: LA CROSSE CLOCK Страницы: 2

Бренд: Jensen Страницы: 9

Бренд: Galleon Страницы: 13

Бренд: Masterclock Страницы: 38

Бренд: Hama Страницы: 19

Бренд: La Crosse Technology Страницы: 20

Бренд: Weems & Plath Страницы: 2

Бренд: Sangean Страницы: 1

Бренд: ETT Страницы: 24

Walkman ICF-CD553RM

Бренд: Sony Страницы: 50

Walkman ICF-CD543RM

Бренд: Sony Страницы: 50

Бренд: Transonic Страницы: 6

Бренд: Datexx Страницы: 1

Бренд: IKEA Страницы: 16

Бренд: Muji Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды