PT AMC123 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 104

background image

Chapter 2: Introduction

28

COM1

The AMC123 payload includes two 16C550, PC-compatible serial ports. When configured
appropriately, COM1 is available for general use at the RJ9 connector on the front panel.
COM1 supports data transfers at speeds up to 115.2 Kb/sec with BIOS support. The baud rate
for BIOS supported console redirection defaults to 9600 and is set in the BIOS setup utility. See

“BIOS Configuration Overview,” on page 46

for more information about BIOS setup. For COM1

port pinout information, see

“COM1 Serial Port Connector (J4),” on page 84

COM2

COM2 is dedicated to communication with the payload serial interface on the MMC. See

Interface Subsystem,” on page 61

for more information about serial communication with the

MMC. Note that the baud rate of COM2 must match the baud rate of the payload serial
interface on the MMC.

Caution:

Be careful to insert the RJ9 connector on the management cable into the serial port only.
Inserting it into an Ethernet connector may damage the Ethernet connector pins. See

3-2, “RJ9 Cable Connection,” on page 40

.

AMC Interface

The AMC123 is compliant with the

AdvancedMC Advanced Mezzanine Card Base

Specification, PICMG AMC.0 R2.0

. It is designed to be hot swappable into a mid-size bay on a

MicroTCA® chassis or an AMC carrier board, as shown in

Figure 2-3, “AMC123 Module

Installed in an AMP507x 1U MicroTCA Platform,” on page 29

It can also function in a non-hot swap AMC system. Its AMC card edge connector provides rear
I/O connectivity to the AMC bus in accordance with the

AMC Type 4 Specification

(see

“AdvancedMC Card Edge Connector (P1),” on page 80

, for more information).

The AMC123 AMC card edge connector supports the following PICMG subsidiary
specifications:

•

AMC.1 (PCI Express), Type 1 — Ports 4-11, x8 PCI Express channels

•

AMC.2 (1GbE), Types E1 and E2 — Port 0 and Port 1, 1Gb Ethernet channels

•

AMC.3 (Storage), Type 1 — Port 2 and Port 3, Dual SATA channels

Connector locations and pinouts are documented in

“AdvancedMC Card Edge Connector

(P1),” on page 80

and

Chapter 10, “Data Sheet Reference,” on page 103

contains links to the

PICMG Web site, where the specification may be obtained.

«
...
26
27
28
29
30
...
»

Содержание AMC123









































































































Отзывы:

Нет отзывов

Похожие инструкции для AMC123

Бренд: Zenith Страницы: 8

Бренд: Fairchild Страницы: 8

Sound Palette SP2400

Бренд: Mackie Страницы: 28

Бренд: Hagerman Страницы: 7

Бренд: Monacor Страницы: 20

Бренд: SKP Pro Audio Страницы: 12

Бренд: Xtant Страницы: 2

Бренд: Warmenfat Страницы: 12

Бренд: AMC Страницы: 9

Бренд: Ltc Audio Страницы: 57

REFERENCE PHONO 10

Бренд: Audio Research Страницы: 18

Бренд: W.E.S.T. Elektronik Страницы: 48

Бренд: Macrom Страницы: 17

AFD100 Slash Signature

Бренд: Marshall Amplification Страницы: 6

Бренд: Magnat Audio Страницы: 7

Бренд: Teac Страницы: 48

Бренд: Saluki Страницы: 85

Бренд: Serene Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды