PT AMC123 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 104

background image

Chapter 3: Getting Started

48

7. Press

<Enter>

. OK is highlighted.

8. Press

<Enter>

to exit the BIOS setup utility.

9. Boot the AMC123.

To set USB Port 1 to the AMC card edge.

1. Look at back of the AMC123. Set SW4-3 to the CLOSED Position (ON). See

“SW4-3 — USB Port 1

Control,” on page 44

.

2. Install the module and boot to the BIOS setup utility by hitting the F2 key while the module is booting

up.

3. In the

Advanced

tab, select

USB Configuration

.

4. Set the configuration for Port 1 to

AMC Card Edge

.

5. Press

<Esc>

to exit to the main menu.

6. Right arrow to select the

Exit

menu item.

Save Changes

and

Exit

is highlighted.

7. Press

<Enter>

.

OK

is highlighted.

8. Press

<Enter>

to exit the BIOS setup utility.

9. Boot the AMC123.

Integrating the AMC123 with an External Hard Drive Module

The following section describes how to integrate the AMC123 with an external hard drive
module, such as PT’s AMC590, by modifying the BIOS settings on the AMC123.

The AMC123 supports two different modes of operation on the SATA interface: Enhanced IDE
mode and Advanced Host Controller Interface (AHCI) mode, at speeds of 1.5 Gbps and 3.0
Gbps. By default the BIOS is set to operate in Enhanced IDE Mode at 3.0 Gbps.

If a SATA I hard drive is installed with a 1.5 Gbps interface on the AMC590, the BIOS may not
detect the hard drive as being installed. For the BIOS to detect the drive, you must change the
BIOS settings on the AMC123. Slowing down the interface in AHCI Mode to 1.5 Gbps allows
for proper negotiation of the SATA I interface.

To Set the IDE and AHCI Configuration to 1.5 Gbps

1. Install the module and boot to the BIOS setup utility by hitting the F2 key while the module is booting

up.

2. Go to the

Advanced

tab, select

IDE Configuration

.

3. Under

IDE Configurations

see if the speed of the hard drive can be controlled. If yes, set the speed

to

1.5 Gbps

for the corresponding IDE port.

4. If you can’t change the hard drive speed, select

Operation Mode for IDE

. Change the mode from

Enhanced

to

AHCI

.

5. Press <Esc> to exit this screen.

6. Go to the

AHCI Configuration

screen.

«
...
46
47
48
49
50
...
»

Содержание AMC123









































































































Отзывы:

Нет отзывов

Похожие инструкции для AMC123

Бренд: Harman Страницы: 2

Бренд: Harley Benton Страницы: 12

Бренд: D.A.S. Страницы: 11

Бренд: Factor Страницы: 12

Бренд: Precision Power Страницы: 12

Бренд: Synaestec Audio Страницы: 10

Бренд: QSC Страницы: 35

Бренд: zapco Страницы: 12

Бренд: DSM Страницы: 8

Бренд: Inter-m Страницы: 10

Бренд: Sansui Страницы: 32

Бренд: Marantz Страницы: 86

Бренд: DaytonAudio Страницы: 14

1812R Blues King 12

Бренд: SUPRO Страницы: 8

Бренд: FONESTAR Страницы: 13

Бренд: Luxman Страницы: 11

Бренд: Harman Kardon Страницы: 6

Бренд: A-Designs Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды