PT AMC123 Скачать руководство пользователя страница 85

Страница: 85 / 104

Internal Connectors

The AMC123 contains the following internal connectors. See

for connector locations.

DDR2 SDRAM Connector

A 90°, 200-pin connector accommodates a single 200-pin, 333.5 MHz PC2-5300 (64-bit +
ECC) SDRAM SO-RDIMM Registered SDRAM used for system memory. For more information
about system memory, see

“Memory Configuration,” on page 36

uSSD/SDM Storage Interface Connector (P5)

The AMC123 includes a 20-pin header that supports the installation of one of the following
storage modules for on-board flash storage:

•

A standard USB storage module (uSSD) with a USB 2.0 interface

•

A standard SATA disk module (SDM) with a SATA II interface

See

Table 5-6, “uSSD/SDM Storage Connector Pinout,” on page 85

for pin definitions.

Table 5-6:

uSSD/SDM Storage Connector Pinout

Pin

Signal Name

Pin

Signal Name

V3V

GND

PHY_RDY_N

TXP

GND

TXN

V5V

GND

USB_N

USB_P

GND

KEY

RXN

GND

RXP

ACTIVITY_LED_N

GND

Содержание AMC123









































































































Результаты поиска

Содержание AMC123

Отзывы:

Похожие инструкции для AMC123

Бренды по названию

Популярные бренды

PT AMC123, Руководство пользователя

Результаты поиска

Содержание AMC123

Отзывы:

Похожие инструкции для AMC123

Бренды по названию

Популярные бренды