PT AMC123 Скачать руководство пользователя страница 21

Страница: 21 / 104

AMC123 Features

•

AMC card edge interface contains:

– up to two Serializer/Deserializer (SerDes) 1Gb Ethernet channels

– eight-lane PCI Express bus

– two SATA channels

– one USB connection

•

Front panel connectivity supports:

– up to two 10/100/1000

Mbps

Ethernet ports via RJ45 connectors

– one USB 2.0 port

– one RS232 serial port with 15 KV electrostatic discharge (ESD) protection

•

Supports up to 4 GB of 64-bit 333.5 MHz PC2-5300, DDR2-667, SDRAM (with ECC) in a 200-pin
SODIMM connector socket

•

Supports up to 16 GB of flash storage via two options:

– a USB solid-state disk drive (uSSD) with a USB 2.0 interface

– a SATA solid-state disk module (SDM) with a SATA II interface

•

Optionally, a solid-state double data rate (SSDDR) module combines a SATA solid state drive (SATA
SSD) and DDR synchronous dynamic RAM (DDR SDRAM) technologies in a single SODIMM
package

•

System management bus (SMBus)

•

8 or 16 Mb Low Pin Count (LPC)-based Boot PROM

•

PT's Embedded BIOS (AMI BIOS

core) stored in local flash memory

•

Supports Windows XP, Windows XP Embedded, Linux

, and Solaris™ operating systems

•

Supports NexusWare Core CGL OS and development environment

•

IPMI interface on the AMC connector

•

Push-button reset switch

•

LEDs:

– Out-of-Service (OOS) (red/amber) and In Service (IS) (green/amber) (

PICMG Advanced

Mezzanine Card AMC.0 Specification R2.0 indicators

)

– USER LED (green/amber)

– Hot Swap (blue/off)

– Front Panel Ethernet: Link (green/amber), Activity (flashing yellow)

Содержание AMC123









































































































Результаты поиска

Содержание AMC123

Отзывы:

Похожие инструкции для AMC123

Бренды по названию

Популярные бренды

PT AMC123, Руководство пользователя

Результаты поиска

Содержание AMC123

Отзывы:

Похожие инструкции для AMC123

Бренды по названию

Популярные бренды