PRÜFTECHNIK FLUKE VIBGUARD IIoT Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 30

background image

2.3 Safety markings

Please refer to the following figure for the safety markings on the VIBGUARD IIoT. The safety markings must be

observed and must not be concealed or removed. For the variants that are installed in a control cabinet (VIB 7.xxx-

PS), the safety labels must be attached at a suitable point in the control cabinet.

1

Vorsicht! Spannung Attention Danger

VIB 7.8xx-SDH

A yellow sticker each on the housing lock and below the power supply.

VIB 7.8xx-PS

A yellow sticker on the top hat rail.

2

100 - 240V AC / 1,3 A / 50-60 Hz

VIB 7.8xx-SDH

A yellow sticker on the outside of the cable gland for the mains supply.

VIB 7.8xx-PS

A yellow sticker on the top hat rail.

8

Edition: 10.2018

Operation

«
...
6
7
8
9
10
...
»

Содержание FLUKE VIBGUARD IIoT































Отзывы:

Нет отзывов

Похожие инструкции для FLUKE VIBGUARD IIoT

Power Xpert PXM 4000

Бренд: Eaton Страницы: 28

Бренд: Hameg Страницы: 44

Бренд: Hameg Страницы: 60

Бренд: Hameg Страницы: 28

Бренд: HAMAR LASER Страницы: 113

Бренд: Teledyne Hastings Instruments Страницы: 54

Бренд: Keeler Страницы: 54

Бренд: LaMotte Страницы: 32

Бренд: Michell Instruments Страницы: 28

Бренд: 3nh Страницы: 39

Бренд: ICP DAS USA Страницы: 71

Бренд: CONDTROL Страницы: 11

Бренд: Milwaukee Страницы: 17

Бренд: YATO Страницы: 52

Бренд: Heyl Страницы: 2

Бренд: YOSensi Страницы: 27

Бренд: Scheppach Страницы: 20

Бренд: wattwatchers Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды