PRÜFTECHNIK FLUKE VIBGUARD IIoT Скачать руководство пользователя страница 28

Страница: 28 / 30

11 Troubleshooting

The following errors may occur during operation:

Symptom

: Sensor status LED on the system module indicates a fault message (flashing orange).

Possible cause

: Sensor line is interrupted or has short circuited.

Remedy

: Check that the connections on the sensor and system are secure. Exchange any damaged cables

Remedy

: Check the cable connections with the

PRÜFTECHNIK installation checker

(item no. VIB 8.745).

Proceed as follows:

Use a cable with banana plugs and alligator clips to connect the sensor cable to the input terminals

(1)

The three status LEDs on the housing indicate the condition of the sensor cable:

Green LED: OK
Red LED: Short circuit
Yellow LED: Ground loop

If none of the LEDs illuminate during testing and the battery is known to be fresh, then the sensor connection is bro-

ken. The installation checker is powered by a 9V battery. Battery condition can be checked as follows:

Connect the 'BATT. TEST' and 'GROUND' terminals

(2)

If the yellow LED illuminates, then battery voltage is below 5 volts and is no longer sufficient for reliable tes-

ting.

PRÜFTECHNIK-installation checker, VIB 8.745

Symptom

: The SYSTEM LED on the system module does not light up.

Possible cause

: Supply voltage is not applied.

Remedy

: Connect to supply voltage.

Edition: 10.2018

Operation

Содержание FLUKE VIBGUARD IIoT































Результаты поиска

Содержание FLUKE VIBGUARD IIoT

Отзывы:

Похожие инструкции для FLUKE VIBGUARD IIoT

Бренды по названию

Популярные бренды

PRÜFTECHNIK FLUKE VIBGUARD IIoT, Операция

Результаты поиска

Содержание FLUKE VIBGUARD IIoT

Отзывы:

Похожие инструкции для FLUKE VIBGUARD IIoT

Бренды по названию

Популярные бренды