PRÜFTECHNIK FLUKE VIBGUARD IIoT Скачать руководство пользователя страница 24

Страница: 24 / 30

9 Triggering a measurement manually

You can manually trigger an additional diagnostic measurement at any time during the current measurement cycle.

This type of measurement is configured in the OMNITREND Center software in the form of a diagnostics group and

is linked to certain trigger conditions. For example, a threshold violation or an external signal can trigger diagnostic

measurements during the measuring operation.
To trigger a diagnostic measurement manually, proceed as follows:

Click on <System> in the navigation bar. The “System Menu” page is displayed.

Click on <Trigger Diagnostic Group> in the “Administration” field. The "Diagnostic measurement" page is dis-

played.

Select the measurement and click on <Start>.

If the CMS is currently busy with a measurement, the triggered measurement is put “on hold”. The mea-

surement does not start until the other diagnostic measurements (usually triggered automatically by an

alarm) have been completed.

Edition: 10.2018

Operation

Содержание FLUKE VIBGUARD IIoT































Результаты поиска

Содержание FLUKE VIBGUARD IIoT

Отзывы:

Похожие инструкции для FLUKE VIBGUARD IIoT

Бренды по названию

Популярные бренды

PRÜFTECHNIK FLUKE VIBGUARD IIoT, Операция

Результаты поиска

Содержание FLUKE VIBGUARD IIoT

Отзывы:

Похожие инструкции для FLUKE VIBGUARD IIoT

Бренды по названию

Популярные бренды