PRÜFTECHNIK FLUKE VIBGUARD IIoT Скачать руководство пользователя страница 12

Страница: 12 / 30

2.7 Residual hazards and protective measures

VIBGUARD IIoT is verifiably safe assuming it is used as intended. The following damage may occur if operated incor-

rectly or used improperly:

Personal damage
Damage to the system or to the machine

Danger due to running machine!

During installation and maintenance work on the machine, there is a risk of injury from moving machine com-

ponents.

Shut down the entire machine system and secure it against unintentional restarting.

Danger due to electric shock!

There is a risk of injury due to low voltage when working on the switch cabinet when it is open (230 V).

Observe the safety markings on live components.

Before carrying out any installation, repair or maintenance work, disconnect the system from the power sup-

ply, determine that there is no voltage and secure the power supply against being switched on again.

Do not open, repair or modify with power supply VIB 5.965-2.5.

Danger due to improperly laid cables

Personnel may stumble over an improperly laid cable and injure themselves. The cable can be damaged due to

external influences.

Lay the cable in such a way that no one can stumble over it.

Use cable ties or a Velcro fastener to fix the cable in place.

Lay the cable in a cable duct or protective tube.

Damage due to electrostatic discharge

During installation, repair and maintenance work on the system, the electronic components can be damaged if tou-

ched due to electrostatic discharge.

Use an earthing strap if contact with the components cannot be ruled out.

Damage due to contamination

In a loaded industrial environment, the system components may have their function impaired or be damaged due

to contamination or moisture when the switch cabinet is open.

Keep the switch cabinet closed as much as possible.

Incorrect measurements due to electromagnetic interference

High frequency rays or electrostatic discharge in the vicinity of the system and measuring equipment can lead to

incorrect measurements.

Do not lay the sensor cables in the vicinity of heavy current lines.

Select an installation site with low electromagnetic radiation exposure.

Edition: 10.2018

Operation

Содержание FLUKE VIBGUARD IIoT































Результаты поиска

Содержание FLUKE VIBGUARD IIoT

Отзывы:

Похожие инструкции для FLUKE VIBGUARD IIoT

Бренды по названию

Популярные бренды

PRÜFTECHNIK FLUKE VIBGUARD IIoT, Операция

Результаты поиска

Содержание FLUKE VIBGUARD IIoT

Отзывы:

Похожие инструкции для FLUKE VIBGUARD IIoT

Бренды по названию

Популярные бренды