Proxomed Compass 530 страница 18 Скачать руководство пользователя | Manualshive

Страница: 18 / 63

background image

18

It must be ensured, especially when changing the position of the unit without disassembly, that it stands
securely on level ground.

The protective cladding must not be removed. The device may only be operated with the protective
cladding mounted.

The warranty becomes void if modifications are made to the device or electronic devices for control and
measurement are attached that have not been carried out by specialist personnel authorized by the
manufacturer.

Defective parts of the device must be replaced immediately - in this case, it is advisable to stop using
the device until repairs have been made. Use only original accessories, otherwise no liability will be
accepted.

The device may only be opened by proxomed service or authorized personnel.

Do not reach with your hands between the moving bearings/rollers.

3.10

Usage note Butterfly/Butterfly Reverse

CAUTION

After adjusting the arm pads, make sure that the sliding block is completely guided in its
groove. Then tighten the clamping lever. If the sliding block is not completely guided in
its groove, the entire force applied during training will be applied to the fixing screw.
Breakage of this screw cannot be ruled out then.

3.11

Protective cladding

The cladding of the compass® 530 equipment is made of plastic in frosted glass design. The training
devices only comply with the legal requirements for training operation when fitted with protective
cladding.

The protective cladding fitted by the manufacturer must therefore not be removed or modified, as
otherwise the standards on which training operations are based will not be complied with.

3.12

Combination with other products

compass

®

530 devices can be optionally equipped with the smart assist accessory. smart assist is an

active medical device from proxomed Medizintechnik GmbH that contains software. smart assist was
developed and tested according to EN 60601-1.

3.13

Side effects and residual risks

The devices are developed in such a way that no critical side effects can occur. Occasional side effects,
such as muscle soreness and joint pain, may occur, usually after incorrect ergonomic adjustment or after
too intensive training. These symptoms should subside spontaneously after a few days.

«
...
16
17
18
19
20
...
»

Содержание Compass 530
































































Отзывы:

Нет отзывов

Похожие инструкции для Compass 530

D-IMager EKL3104

Бренд: Panasonic Страницы: 13

Бренд: Labokey Страницы: 5

Бренд: E-Z Trail Страницы: 8

Бренд: B&K Страницы: 10

Бренд: LAWO Страницы: 459

Бренд: earline Страницы: 13

Бренд: Faderfox Страницы: 8

Бренд: Quivogne Страницы: 13

Бренд: Abus Страницы: 12

Бренд: Lalizas Страницы: 12

BOBCAT 130 Series

Бренд: Balcrank Страницы: 12

Бренд: Xtricity Страницы: 4

Бренд: Crosley Страницы: 6

Бренд: Gambro Страницы: 273

XMLT-24ELED-200CA8-1

Бренд: DS Produkte Страницы: 28

Бренд: American DJ Страницы: 12

Бренд: aion Страницы: 10

Бренд: COOPS & FEATHERS Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды