Protrol IPC4020 Скачать руководство пользователя страница 60

Страница: 60 / 63

IPC402x-UM-2209-1-2.x.x (en)

Ensto Protrol AB

Phone: +46 31 45 82 00

Alfagatan 3

internet: www.protrol.se

431 49 Mölndal, SWEDEN

e-mail: [email protected]

12 Checklist for Commissioning and Testing

Check the polarity and level of the auxiliary voltage before powering up the IPC402x.

Connect to IPC402x via the Ethernet or USB interface. Log in as

config

admin

Open the

Site

manager

subtab

Test binary inputs by applying 24 VDC at one input at a time. Verify that:

The correct LED on the unit lights up.

The corresponding LED symbol in the

Site manager

is activated.

Corresponding indication message is sent via the selected remote interface.

Check

Enable

Manual control of outputs

box in

Site manager

. If required, disconnect the

outputs from external objects. Verify that:

The correct LED on the unit lights up when activated in

Site manager

The correct output is activated. Measure the resistance across the output on
terminal block. It should be < 1 Ohm when the relay is active.

If possible, activate the output via the remote interface.

If the station is in operation, the phase currents connected and with a measurable current,
check that:

The correct amplitude is displayed in the

Site manager

The currents are symmetrically presented in

Site manager

. If the amplitudes are

equal and the residual current near 0 is safe, the connection is correct.

Create a disturbance file and check that the phase sequence is the expected one.

Measurement values are displayed correctly in the remote control center.

Содержание IPC4020
































































Результаты поиска

Содержание IPC4020

Отзывы:

Похожие инструкции для IPC4020

Бренды по названию

Популярные бренды

Protrol IPC4020, Руководство пользователя

Результаты поиска

Содержание IPC4020

Отзывы:

Похожие инструкции для IPC4020

Бренды по названию

Популярные бренды