manualshive.com logo in svg

ProSoft Technology inRA-x ILX34-AENWG, Руководство по установке

Поделиться
Скачать
ProSoft Technology inRA-x ILX34-AENWG Скачать руководство пользователя страница 37

Procedures ILX34-AENWG 

♦

 POINT I/O Platform 

Setup Guide 

Wireless Point I/O Adapter 

 

 
ProSoft Technology, Inc. 

Page 37 of 79 

July 31, 2009 
 

5 

Click 

OK

 

save the configuration. 

The following illustration shows the I/O Configuration for this project. 

 

Download the Sample Program to the Processor 

Note: 

The key switch on the front of the ControlLogix processor must be in the 

REM

 

or 

PROG

 

position. 

1 

If you are not already online with the processor, open the 

C

OMMUNICATIONS 

menu, and then choose 

D

OWNLOAD

.

 

RSLogix will establish communication 

with the processor. 

2 

When communication is established, RSLogix will open a confirmation dialog 
box. Click the 

D

OWNLOAD 

button to transfer the sample program to the 

processor.  

 

3 

RSLogix will compile the program and transfer it to the processor. This 
process may take a few minutes.  

4 

When the download is complete, RSLogix will open another confirmation 
dialog box. If the keyswitch is in the 

REM

 position, click 

OK

 

to switch the 

processor from 

Program 

mode to 

Run 

mode. 

 

Note: 

If you receive an error message during these steps, refer to your RSLogix documentation to 

interpret and correct the error.  

Содержание inRA-x ILX34-AENWG
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды