ProSoft Technology inRA-x ILX34-AENWG Скачать руководство пользователя страница 10

Страница: 10 / 79

ILX34-AENWG

♦

POINT I/O Platform

Scope

Wireless Point I/O Adapter

Setup Guide

Page 10 of 79

ProSoft Technology, Inc.

July 31, 2009

Additional documentation, tools, and product support

Email Technical Support:

Send your support questions to Support@prosoft-

technology.com

Web Site Support:

Visit the ProSoft Technology web site at

www.prosoft-technology.com to download additional documentation, tools
and application information

Telephone Support:

Please call ProSoft Technology Technical Support at:

(Country Code 1+) 661-716-5100. Support is available 24 hours a day, 7
days a week. ProSoft Technology telephone support is free and unlimited

1.3 Prerequisites

To get the most benefit from this setup guide, you should have the following
skills:

Rockwell Automation

RSLogix 5000™ software:

launch the program,

load the Add-On Profile, and configure the project.

Microsoft Windows:

install and launch programs, execute menu commands,

navigate dialog boxes and enter data.

Ethernet networking:

connect the ILX34-AENWG adapter to an Ethernet

network using a valid IP address and subnet mask

Wireless networking:

correctly configure the adapter to communicate on an

802.11b/g wireless network

Hardware installation and wiring

: install the adapter and safely connect

POINT I/O devices to the ILX34-AENWG adapter's chassis

1.3.1 System

Requirements

The ILX34-AENWG adapter requires the following minimum hardware and
software components:

Rockwell

Automation

processor, with compatible power supply

ControlLogix™ 1756-L6x (firmware version 17.03 or higher), or 1756-6xS
(firmware version 17.07 or higher)
or

CompactLogix™ 1769-L32E or 1769-L35E, (firmware version 17.04 or
higher)

Rockwell Automation RSLogix 5000 programming software version 16 or

higher. Version 17 is required if you wish to use the ILX34-AENWG Add-On
Profile.

Rockwell Automation RSLinx communication software version 2.54 or higher

An 802.11g Radio. ProSoft recommends the RLXIB-IHW 802.11 a/b/g

Industrial Hotspot (page 18).

If you plan to use the ILX34-AENWG with a 1756-ENBT module or 1768-

ENBT module, note the following firmware version requirements:

1756-ENBT firmware revision 4.007 or later

1768-ENBT firmware revision 2.003 or later

Use BootP revision 2.3.2 or later to assign IP addresses to the adapter.

Содержание inRA-x ILX34-AENWG
















































































Результаты поиска

Содержание inRA-x ILX34-AENWG

Отзывы:

Бренды по названию

Популярные бренды

ProSoft Technology inRA-x ILX34-AENWG, Руководство по установке

Результаты поиска

Содержание inRA-x ILX34-AENWG

Отзывы:

Бренды по названию

Популярные бренды