manualshive.com logo in svg

ProSoft Technology inRA-x ILX34-AENWG, Руководство по установке

Поделиться
Скачать
ProSoft Technology inRA-x ILX34-AENWG Скачать руководство пользователя страница 22

ILX34-AENWG 

♦

 POINT I/O Platform 

Procedures 

Wireless Point I/O Adapter  

Setup Guide 

 

 
Page 22 of 79  

ProSoft Technology, Inc. 

July 31, 2009 

 

When you power up the POINT I/O for the first time, the adapter must assign 
addresses to every module in the backplane. POINT I/O modules are all initially 
configured at the same address. 

When you first apply power, all but one module on the backplane should show a 
solid red Module Status LED. 

One by one, the adapter resets these modules and assigns addresses. The 
amount of time that this operation takes depends on the size of your POINT I/O 
system. 

3.2.6  Connect the Adapter to the EtherNet/IP Network 

Connect an Ethernet cable between the adapter’s Ethernet port, and the 
EtherNet/IP network.  

Note: 

This connection is temporary, and is helpful during configuration. You will disconnect the 

Ethernet cable after you have finished configuring the adapter for wireless communication.  

 

Содержание inRA-x ILX34-AENWG
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды