ProMinent TUC 1 Скачать руководство пользователя страница 22

Страница: 22 / 76

4. Hose connector. 4.75 mm interior

diameter, 8 mm external diameter.

Hose connection to the sampling site

5. Detail: Hose

6. Detail: Union nut hose connection

7. Detail: Replacement hose connection

8. Shut-off clamp. To shut-off the inlet in

an emergency or for necessary work

4.3 Installation (electrical)

WARNING!

Live parts!
Possible consequence: Fatal or very

serious injuries
–

Measure: Disconnect the power

supply before opening the

housing

–

Disconnect damaged, defective

or manipulated devices from the

power supply

–

The provision of a suitable iso‐

lating device (emergency-off

switch, etc.) is the responsibility

of the plant operator

NOTICE!

Do not route any RS-485 cables in

the same cable duct as the power

supply cable. This may result in major

anomalies.

The signal leads of the

DULCO

turb C may not be routed

alongside faulty cabling. Faults could

lead to malfunctions in the

DULCO

turb C.

Assembly and Installation

Mahar Fan

Содержание TUC 1













































































Результаты поиска

Содержание TUC 1

Отзывы:

Бренды по названию

Популярные бренды

ProMinent TUC 1, Руководство по сборке и эксплуатации

Результаты поиска

Содержание TUC 1

Отзывы:

Бренды по названию

Популярные бренды