PROEL BM0900 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 54

background image

42

11.6.2.

Hotel numbering (storey)

In some blocks, the apartment number starts with a prefix indicating the floor number. It is a hotel
number (floor number). PC255 decoders can be addressed up to 255, and therefore, in case of a
block with such numbering, there is a need to apply hotel conversion built into the PBX. Thanks to
this it is possible to limit the range of physical numbers while maintaining large logical numbers.

The  algorithm  that  converts  logical
numbers into physical numbers, in case of
floor  numbering,  is  similar  to  linear
numbering  (see  section  11.6.1).  The
difference  consists  in  adding  one  degree
calculating  the  number  on  the  basis  of
settings

“

degree of numbering division

”

and

“

number of premises on the first floor

”

(par. 203 and 204). The algorithm is shown
in Figure 13.

Unlike CD1803, the KDC3905 control panel
enables to change the degree of division of
hotel  numbering  (i.e.  how  many  digits  on
the  front  of  number  is  the  floor  number).
Please note that the maximum number of
premises  on  the  floor  is  limited  to  99.  To
enable hotel numbering, set the numbering
level parameter to a value different from 0.
The  numbering  level  defines  how  many
youngest digits is the number of premises
on the floor.

Physical number to which the decoder will
be addressed is calculated according to the
formula:

No.

ind.

=

No.

log

±

PreShift

No.

phy.

= (

No.

floor

−

1)

·

NumberOfPremisesOnTheFloor

+

No.

premise

±

PostShift

Where

No.

floor

and

No.

premise

are obtained from an indirect number, according to Table 11. If the

obtained number of the premises is greater than the Number of premises on the floor parameter,
the PBX will signal this on the keyboard, and then the connection will be interrupted.

Numer

Logiczny

Postshift

par. 205

Numer znajduje się

w zakresie <min;max>

numerów fizycznych?

Par. 206;207

Numer fizyczny

Wyjście

Wyjście

Preshift

Par 202

Numer jest w

tablicy przekierowania A2

lub na liście lokatorów?

Numer znajduje się

w zakresie <min;max>

numerów logicznych?

Par. 200;201

Preshift zdalny

(od mastera)

Par. 210

Nie

Tak

Nie

Tak

Nie

Tak

Przeliczenie hotelowe

Par 203;204;205

Figure 13. Dataflow algorithm converting logical numbers into physical numbers
(hotel numbering)

«
...
44
45
46
47
48
...
»

Содержание BM0900























































Отзывы:

Нет отзывов

Похожие инструкции для BM0900

Бренд: Cooler Master Страницы: 39

Бренд: Azio Страницы: 5

Бренд: TYPHOON Страницы: 2

Бренд: Memorex Страницы: 37

Lycosa Gaming Keyboard

Бренд: Razer Страницы: 24

Bluetooth Keyboard for Tablets

Бренд: Targus Страницы: 7

Бренд: Targus Страницы: 5

Бренд: Targus Страницы: 52

Бренд: BELEDU Страницы: 23

Бренд: Hama Страницы: 21

Бренд: Olimpia electronics Страницы: 2

Бренд: perixx Страницы: 29

PortaSound PSS-280

Бренд: Yamaha Страницы: 40

Бренд: E-Mu Страницы: 42

Бренд: ViewSonic Страницы: 13

Бренд: TT Tech Страницы: 10

EG-101 groovekeyboard

Бренд: Roland Страницы: 62

Бренд: Cherry Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды