background image

 

62

cold water and a very very soft cloth when rubbing is required.  Do not use paper towels or Terri-cloth towels.  Try 
not to use any cleaning solutions, as most will cause yellowing and cracking. 
 
When you have to store the panels of your Windscreen and Curtain Package, always “roll up” the material to 
prevent 

creases

.  Do not fold the Isinglass as this will permanently damage the Isinglass material.  Do not roll up 

the panels when wet, as the material will turn white or fog up.  Dry the panels off first using a very very soft cloth 
before rolling them up.  A few hours in the sun will get rid of the whiteness or fogginess in most cases. 
 

Vinyl

 

 

Interior Vinyl - Cabin Headliner and Cabin Bolsters 

Clean periodically to maintain the appearance of the vinyl and to prevent the build-up of dirt and contaminants.  
Any stain, spill or soiling should be cleaned promptly to prevent the possibility of permanent staining.  When 
cleaning, always scrub gently using a soft cloth or nylon bristle brush. 
 

Caution:  Powered abrasives, abrasive cleaners and steel wool will damage vinyl, as do strong 
solvents, lacquer solutions and inks.  Lotions, suntan oil, waxes and polishes, etc., contain oils 
and dyes that can cause stiffening and staining of the vinyl.  Never use steam, heat guns or hair 
dryers. 

 
For additional information regarding the care and maintenance of this product, please refer to the Morbern 
brochure provided in your owner’s package for recommended methods to clean specific types of stains. 
 

Exterior Vinyl – Upholstered Seats and Cockpit Bolsters 

Vinyl requires periodic cleaning to maintain its neat appearance and to prevent the build-up of dirt and 
contaminants that may permanently stain and reduce the life of the vinyl if they are not removed.  The frequency 
of cleaning depends on the amount of use and on environmental conditions to which the vinyl is subjected.  The 
procedures used for cleaning are dependent upon the end use circumstances. 
 
For normal cleaning, most stains can be cleaned using warm soapy water and a clear water rinse.  Moderate 
scrubbing with a medium bristle brush will help to loosen soiling material from the depressions of embossed 
surfaces.  For stubborn stains, use either Fantastic or Mr. Clean, which are commercially available mild 
detergents, in accordance with manufacturers instructions. 
 
For additional information regarding the care and maintenance of this product, please refer to the Morbern 
brochure provided in your owner’s package for recommended methods to clean specific types of stains. 
 

Cloth 

 

Cabin Cushions, Pillows and Curtains 

The manufacturer of the materials used in making the cabin cushions, pillows and curtains recommends the 
following cleaning procedures: 
 
Spot clean only with water based shampoo or foam upholstery cleaner.  Pretest a small, inconspicuous area 
before proceeding.  Do not over wet.  Do not use solvents to spot clean.  Pile fabrics may require brushing with a 
non-metallic, stiff bristle brush to restore appearance. 
 

Note:  Water extraction or steam cleaning is not a recommended cleaning method.  Cushion 
covers should not be removed and laundered.  To prevent overall soiling, frequent vacuuming or 
light brushing with a non-metallic, stiff bristle brush to remove dust and grime is recommended.  
When cleaning a spill, blot immediately to remove spilled material.  Clean spot stains from the 
outside to the middle of the affected area to prevent circling. 

 
Use a professional furniture cleaning service when an overall soiled condition has been reached. 
 
For additional information regarding the care and maintenance of this product, please refer to the Morbern 
brochure provided in your owner’s package for recommended methods to clean specific types of stains. 

Содержание 2010 35 Express













































































Отзывы: