Pro-face PL-6930-T41 Скачать руководство пользователя страница 15

Страница: 15 / 175

PL-6930 / PL-7930 Series User Manual

1-2

1.1

Prior to Operating the PL Unit

The following procedures are prior to use the PL unit.

• After hardware setup is completed, the OS (Windows

2000, Windows

XP) must

be used to create partitions and format (initialize) the HDD before any data or

applications can be saved to the hard disk drive. For details concerning these

procedures, refer to the OS manufacturer's instruction manual.

• Whenever you turn the PL unit's power OFF, wait until the internal HDD stops

spinning (approximately 5 seconds) before turning the power ON again.

• The PL’s hard disk is designed for use with the Windows

2000, Windows

XP.

This driver software can’t be applied to other operating systems.

Connect the display unit and any optional devices.

Connect the PL unit's power cord to AC Intercon-
nection and turn the power switch ON.

Configure the PL unit's BIOS.

Setup an OS for the PL.

Visit the download page at the Otasuke Pro! site.

URL http://www.pro-face.com/otasuke/

Setup the pre-installed PL.

Install all required software. For software instal-
lation instructions, refer to the manual provided
with that product.

SEE

1.2 System Design (page1-6)/1.3
Accessories (page1-7)

SEE

4.2 Wiring (page4-7)

SEE

5.1 Setup Procedures (page5-2)

SEE

6.1.1 Setting Up an HDD with no

Pre-installed OS (page6-2)

SEE

6.1.2 Setting Up an HDD with Pre-

installed OS (page6-4)

Connect Peripheral Devices

Connect Power

Set Up the System

Install an OS

Download and install the neces-

sary divers and utility software

Install Required Software

Install the PL Unit

[When PL has no preinstalled OS]

Install a commercial
OS in your PL. For
how to setup the OS,
refer to the manual
provided with the
product.

[When PL has preinstalled OS]

Содержание PL-6930-T41
















































































































































































Результаты поиска

Содержание PL-6930-T41

Отзывы:

Похожие инструкции для PL-6930-T41

Бренды по названию

Популярные бренды

Pro-face PL-6930-T41, Руководство пользователя

Результаты поиска

Содержание PL-6930-T41

Отзывы:

Похожие инструкции для PL-6930-T41

Бренды по названию

Популярные бренды