Pro-face PL-6930-T41 Скачать руководство пользователя страница 140

Страница: 140 / 175

Chapter 7 PL Monitoring Features

7-15

7.3.2

Error Type/Location and Error Action

Error Type/Location

The error types/locations shown by the Event Viewer are as follows.

Error Action

Using the Eveint Viewer the following actions can be taken when an error occurs

Error Type

Message

Voltage VcoreA

VOLT VcoreA Error has occurred.

Voltage VcoreB

VOLT VcoreB Error has occurred.

V3.3V

VOLT +3.3V Error has occurred.

V5.0V

VOLT +5.0V Error has occurred.

V12.0V

VOLT +12V Error has occurred.

Voltage -5.0V

VOLT -5.0V Error has occurred.

Voltage -12.0V

VOLT -12V Error has occurred.

CPU FAN

FAN CPU Error has occurred.

System FAN

FAN System Error has occurred.

Temperature CPU

TEMP CPU Error has occurred.

Temperature
System

TEMP System Error has occurred.

Temperature
System2

TEMP System2 Error has occurred.

DIN0

DIN0 Error has occurred.

DIN1

DIN1 Error has occurred.

DIN2

DIN2 Error has occurred.

DIN3

DIN3 Error has occurred.

Watchdog

Watchdog Timer Error has occurred.

Backlight

Backlight Error has occurred.

SMART

SMART Error has occurred. Attribute (No.)(Attribute Name) Device
(No.)(HD Model).
The descriptions in the parentheses vary depending on details of occurring
errors and the device where errors occur (0:Master, 1:Slave)

•

The data shown in the table’s “

” indicate the error type/location.

•

The actions to be taken after an error occurs are set via the System Monitor Property screen.

Содержание PL-6930-T41
















































































































































































Результаты поиска

Содержание PL-6930-T41

Отзывы:

Похожие инструкции для PL-6930-T41

Бренды по названию

Популярные бренды

Pro-face PL-6930-T41, Руководство пользователя

Результаты поиска

Содержание PL-6930-T41

Отзывы:

Похожие инструкции для PL-6930-T41

Бренды по названию

Популярные бренды