Price FFU series Скачать руководство пользователя страница 7

Страница: 7 / 42

FAN FILTER UNIT

INSTALLATION INSTRUCTIONS

ECMSC

Installation

Sample line string:

FFU-HE/24/48/RSR/BC/ECM/115/10//CT//HEPA//

ECMSC

/DSW/PC/TMB/ATS/ML/FL/WPF/PL-AL/F-

AL/PL-B12/F-B12

If FFUCS-WMSC-30 was not provided, proceed to Step 4.

Step 1:

Wire the unit according to appropriate wiring diagram. If Power Cord (PC) option is selected, simply insert plug end into

electrical socket.

Sample line string:

FFU-1-X//I/SUPPLY/24/48//BTR/HEPA/FC/ECM/115/CF/TMB//ECMSC/TC/DSW-115/

PC-115

/ASSP///WPF/PL-AL/F-EM/PL-

WM/F-EM

Step 2:

If ECMSC is to be controlled using analog voltage signal from BAS (others) or Price WMSC, please remove ECMSC from

control box. Connect 0-10VDC & COMMON to BAS SIGNAL & BAS COMMON on back of ECMSC (make sure to feed wires
through grommet on control box). Re-fasten ECMSC to control box.

Step 3:

If the unit has an RSR filter install the filter now, refer to the filter installation section of this manual for instructions.

Step 4:

Ensure proper Voltage is hooked up to the unit.

ECMSC

priceindustries.com | FAN FILTER UNIT - Manual

Содержание FFU series










































Результаты поиска

Содержание FFU series

Отзывы:

Похожие инструкции для FFU series

Бренды по названию

Популярные бренды

Price FFU series, Инструкция по установке и обслуживанию

Результаты поиска

Содержание FFU series

Отзывы:

Похожие инструкции для FFU series

Бренды по названию

Популярные бренды