Price FFU series Скачать руководство пользователя страница 13

Страница: 13 / 42

FAN FILTER UNIT

INSTALLATION INSTRUCTIONS

Step 2:

For local control, adjust at the speed controller using the up and down arrows. For BACnet control, adjust point "AO3 -

ECM Setpoint" on Front End System.

Step 3:

For BAS analog voltage control, ensure correct voltage is applied to AI1 & COM based on the VDC equations provided in

the tables. Also refer to table below for BAS control responses.

BAS Voltage

Response

Notes

0 - 1 VDC

Local control mode using push buttons

Local setpoint can be adjusted from 0 - 100% using push buttons

1 - 2 VDC

Motor Off

Recommended sending a 1.5 VDC signal to command motor off

2 - 10 VDC

Modulating Control

2 - 10 VDC modulates motor in accordance with VDC equations

The VDC equations are based on a 1-5 Volt scale. The BAS input voltage is a 2-10 VDC scale, and therefore VDC calculated for a
given CFM using the equations must be doubled to achieve that CFM using the BAS input.

NOTE:

The calculated ECM setpoint is a starting point; actual value may differ slightly depending on field variables.

NOTE:

The BAS signal will override the local setpoint using a remote 0 – 10 VDC signal. If the BAS signal drops below 1 VDC local

control (via the up/down buttons) is restored.

Step 4:

Wait a few seconds for the ECM motor to adjust its speed and then verify fan airflow with measurements at the supply

outlets using a flow hood. Adjust voltage to reach desired airflow as required.

Step 5:

Proceed to

Balancing

section of this manual.

Exhaust - Constant Flow – Clean Filters (Forward Curved)

Voltage

Velocity

24 x 48

Volt

FPM

RSR - FC

115

45-135

ECM% = (CFM/7.63) - 18

240

45-135

ECM% = (CFM/7.63) - 18

277

45-135

ECM% = (CFM/7.53) - 18

Exhaust - Constant Torque – Clean Filters (Forward Curved)

Voltage

Velocity

24 x 48

Volt

FPM

RSR - FC

115

45-90

ECM% = (CFM/13.09) - 6

90-135

ECM% = (CFM/7.77) - 30

240

45-90

ECM% = (CFM/13.3) - 6

90-135

ECM% = (CFM/7.74) - 30

277

45-90

ECM% = (CFM/13.09) - 6

90-135

ECM% = (CFM/7.63) - 31

priceindustries.com | FAN FILTER UNIT - Manual

Содержание FFU series










































Результаты поиска

Содержание FFU series

Отзывы:

Похожие инструкции для FFU series

Бренды по названию

Популярные бренды

Price FFU series, Инструкция по установке и обслуживанию

Результаты поиска

Содержание FFU series

Отзывы:

Похожие инструкции для FFU series

Бренды по названию

Популярные бренды