PowerTek MC642 Скачать руководство пользователя страница 69

Страница: 69 / 73

7. Maintenance

This chapter explains how to perform the routine maintenance to keep your device in optimal

operating condition. The tasks covered in this chapter include the following:

Fuse replacing

External surface cleaning

7.1. Fuse replacing

The instrument includes a fuse located in the mains connector at the rear panel. Replace the fuse as

follows:

Switch off the decade box

Remove the end of power cord from the mains connector at the rear panel.

Insert the blade of a flat screwdriver into the opening cut in the mains voltage selector and pull out the
fuse holder.

Remove the fuse and replace it with new fuse of the same rating.

7.2. External surface cleaning

To keep the device looking like new, clean the case and front panel keys using a soft cloth slightly

dampened with either water or a non-abrasive mild cleaning solution that is not harmful to plastics.

8. Module 19” (version MC642-Vxx1x)

Decade can be ordered as 19” module for easy assembling into a 19” rack. Module height is 3HE.

Figure 30 Module 19" rack, front panel

Operation manual

Содержание MC642










































































Результаты поиска

Содержание MC642

Отзывы:

Бренды по названию

Популярные бренды

PowerTek MC642, Руководство по эксплуатации

Результаты поиска

Содержание MC642

Отзывы:

Бренды по названию

Популярные бренды