manualshive.com logo in svg

PowerTek MC642, Руководство по эксплуатации

Поделиться
Скачать
PowerTek MC642 Скачать руководство пользователя страница 29

6.3.

LAN Interface (option)

LAN Interface allows communication with decade box using Telnet protocol. A proper setting must be

established.

Following equipment is required:

!

MC642 decade box with LAN, USB, IEEE488 bus option

!

Personal Computer (or other controlling device) with LAN interface

!

LAN cable

The LAN interface must be selected from decade system menu to be in operation (

SETUP->Interface-

>Active bus

). There are following LAN settings accessible from decade system menu under

SETUP-

>Interface->LAN Settings

 path (values are default ones):

DHCP

ON

IP Address

192.168.001.100

only valid if DHCP is OFF

Subnet mask255.255.255.000

only valid if DHCP is OFF

Default gateway

255.255.255.255

only valid if DHCP is OFF

Port number

23

Host name

MC642_SN620031

only valid if DHCP is ON

If DHCP (Dynamic Host Configuration Protocol) is enabled, the IP Address and all necessary settings are
done automatically and connection in Telnet protocol is done via “Host name” and “Port number”.
Otherwise the IP address, Subnet mask and Default gateway should be properly set. In this case connection
is done via “IP Address” and “Port number”.
 
Connection to decade box using Microsoft Telnet terminal with DHCP option enabled:

Figure 26 LAN connection 1

If connection is successful following screen will appear:

Figure 27 LAN connection 2

      

   

29

   

 

                                                        

 

 

 

                                                    

 

 

 

   

Operation manual

 

 

Содержание MC642










































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды